Given that This circuit runs on the flashbulb of a camera. Circuit is powered by 4 AA batteries each in series that are 1.5 V. The capacitor is C=50 mF when the switch makes contact on the left that is charged through the resistor that is. R1=10 ohm Switch in contact on the right, the capacitor discharges through the flashbulb with a A resistance of R2 = 1m2 that produces light. • What would be the average power of the light, during the time period of the flash. (please give answer in 2 significant digits) • What's the time duration in (us) of the the flash lasts after the capacitor is at a charge of 90 percent of total energy. When the capacitor is discharged through the bulb and the switch is switched to the right. Further knowing, that the light the bulb gives off has a potential across that is more than 1V) (2 sig figs)

Given that This circuit runs on the flashbulb of a camera. Circuit is powered by 4 AA batteries each in series that are 1.5 V. The capacitor is C=50 mF when the switch makes contact on the left that is charged through the resistor that is. R1=10 ohm Switch in contact on the right, the capacitor discharges through the flashbulb with a A resistance of R2 = 1m2 that produces light. • What would be the average power of the light, during the time period of the flash. (please give answer in 2 significant digits) • What's the time duration in (us) of the the flash lasts after the capacitor is at a charge of 90 percent of total energy. When the capacitor is discharged through the bulb and the switch is switched to the right. Further knowing, that the light the bulb gives off has a potential across that is more than 1V) (2 sig figs)

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 74AP: Consider a circuit that consists of a real battery with an emf and an internal resistance of r...

See similar textbooks

Similar questions

Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
For the circuit shown in Figure P28.55. the ideal voltmeter reads 6.00 V and the ideal ammeter reads 3.00-k. Find (a) the value of K, (b) the emf of the battery, and (c) the voltage across the 3.00-kft resistor.
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
Consider the circuit shown below. The terminal voltage of the battery is V = 18.00 V. (a) Find the equivalent resistance of the circuit, (b) Find the current through each resistor, (c) Find the potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the power supplied by the battery.
Digital medical thermometers determine temperature by measuring the resistance of a semiconductor device called a thermistor (which has a=0.06/C ) when it isat the same temperature as the patient. What is a patient’s temperature if the thermistor’s resistance at that temperature is 82.0% of its value at 37C (normal bodytemperature)?
A battery with an internal resistance of 10.0 produces an open circuit voltage of 12.0 V. A variable load resistance with a range from 0 to 30.0 is connected across the battery. (Note: A battery has a resistance that depends on the condition of its chemicals and that increases as the battery ages. This internal resistance can be represented in a simple circuit diagram as a resistor in series with the battery.) (a) Graph the power dissipated in the load resistor as a function of the load resistance. (b) With your graph, demonstrate the following important theorem: The power delivered to a load is a maximum if the load resistance equals the internal resistance of the source.
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19