Given the circuit below with Vs = 25V, Rs =2k2, RL = 4KO, and Vz 12V:RsIR+ VR -+VsVz Za) Verify if the diode will be ON or OFF,show your calculations. 11Calculate the voltage VL across an i theb)current IL through the load resistor RL. I'c)Calculate the voltage VR across and thecurrent IR through the resistor Rs. ISd)Calculate the current across the diodeIz. .e)What is the type of diode used in thecircuit above? Explain in your own words itsoperation? [E.+

Given the circuit below with Vs 25V, Rs = 2k2, RL = 4KQ, and Vz = 12V: %3D Rs ww Vz Z + + Vr - IR + V s a) Verify if the diode will be ON or OFF, show your calculations. [1 b) Calculate the voltage VL across ani the current IL through the load resistor R1. I c) Calculate the voltage VR across and the current IR through the resistor Rs. IS +

Given the circuit below with Vs 25V, Rs = 2k2, RL = 4KQ, and Vz = 12V: %3D Rs ww Vz Z + + Vr - IR + V s a) Verify if the diode will be ON or OFF, show your calculations. [1 b) Calculate the voltage VL across ani the current IL through the load resistor R1. I c) Calculate the voltage VR across and the current IR through the resistor Rs. IS +

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Similar questions

An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What is CEMF?
How is a solid-state diode tested? Explain.
SENOID INPUTS - HALF WAVE RECTIFICATION 1. Given "Pmax = 14mW" for each diode in the figure, determine the maximum current rating for each diode. (use approximate equivalent model) 2. Find "Imax" when Vimax = 160V 3. Determine the current of each "Vimax" diode using the results of literal (2)
Determined the range of values for Vin that will maintain the Zener diode in ON state and power dissipated in diode, for the cct in figure( 3).Vz=30volt, Rs=500Ω, Izmin=5mA,Izmax=80mA,RL=1000Ω
a. Determine VL, IL, and IR for the network of below if RL=180 ohms b. Repeat part (a) if RL=470 ohms c. Determine the value of RL that will establish maximum power condition for the Zener diode. d. Determine the minimum value of RL to ensure that the Zener diode is the the "on" state.
Sketch i0and v01 for the network below for the input shown (Both diodes are Si. VD=0.7 V). Explain your drawings, briefly.
For the half-wave rectifier circuit shown, the diode is not ideal and is modeled as an ideal voltage source of value Vf= 0.65V in series with an ideal diode. Vin= 5sin(2π100t) and R =510Ω. What is the output voltage at time t=24mst=24ms? 2- For the same circuit as in Question 1, what is the output voltage at time t=35.4ms t=35.4ms? Enter your answer in volts 3- For the same circuit as in Question 1, what is the magnitude of the diode current at time t=12mst=12ms? Enter your answer in mA without units.
S-3) Zenerin diode in the zenar voltage regulator circuit given in the figure parameters are Pz = 2.5 W, Vz = 9V, Izmin = 0.45 mA. This zener In order for the circuit to regulate properly, E source Calculate the largest and smallest values of the voltage voltage can take.
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?
Sketch i0 and v01 for the network below for the input shown (Both diodes are Si. Vd = 0.7 V) Explain your drawings, briefly pls.