Given the circuit fed by 50HZ voltage source Vs, knowing that Z, is an inductive load with 0.8 power factor and Zz is a capacitive load with 0.6 power factor, please answer the following questions with detailed steps a) Find the power factor of the parallel of Z1 and Z2. b) Find the phasor Is, ( given V1 = 200<0 Volts) c) Find the lost power in the line. d) Find the voltage of the source Vs. e) Find the value of the capacitor to be added parallel to the loads to have a unity power factor 0.05 + j0.5Q Line 8kW 6 kVA V, 20020° Z1 0.8 | 0.6

Given the circuit fed by 50HZ voltage source Vs, knowing that Z, is an inductive load with 0.8 power factor and Zz is a capacitive load with 0.6 power factor, please answer the following questions with detailed steps a) Find the power factor of the parallel of Z1 and Z2. b) Find the phasor Is, ( given V1 = 200<0 Volts) c) Find the lost power in the line. d) Find the voltage of the source Vs. e) Find the value of the capacitor to be added parallel to the loads to have a unity power factor 0.05 + j0.5Q Line 8kW 6 kVA V, 20020° Z1 0.8 | 0.6

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Similar questions

1.1 We have two loads in delta and another in star in parallel, the impedances of the branches of the delta are equal and we have that RΔ=1p.u. and XΔ=0.75 p.u., while in the star we have equal values of the branches, but formed by admittances where we have the conductance in parallel GY=0.64 p.u. and inductive susceptance of BY=-j0.48 p.u. If the loads are being supplied by a positive sequence balanced three-phase source with line-to-line voltage of phases a and b of Vab=1∠ 30º, if the base values are line-to-line base voltage of 1kV and three-phase base power of 100kW. DetermineA) Line and phase voltages, line and phase currents of the load in delta, line and phase voltages of the star, line and phase currents of the star.B) Obtain separately the phasor diagram of the delta and star load with the values obtained in A), indicate on the scale that these are 1 p.u.=5cm for example.C) obtain the power triangle and the power factor separately for each load. D) Obtain the power…
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the voltage and current at R1, total power (apparent) delivered by the current source, draw the phasor diagram of the voltage and current at the source. Also, is the circuit inductive, capacitive, or neither (resistive)? please give the step-by-step solution NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
PLEASE SOLVE THIS QUICKLY The apparent power of the load Z1 in the circuit given in the figure | S1 | = 16 kVA and at 0.8 back power factor, apparent power of Z2 load is | S2 | = 25 kVA and operates at unit power factor. The loads are connected to the source by ZW = 5 + j26 ohm conductive transmission line. Since the supply voltage of the loads is VL = 3.8 kV, find the apparent power seen by the source, the power coefficient and the effective value of the welding voltage.
In the circuit shown in the figure, there is a load between the terminals a and b, consisting of the series connection of the resistor R0 and the inductance L0. The amplitude of the voltage Vs (t) is two root hundred and fifty phase angle Qs = zero degree period T = 200 PI microseconds. Since R = 300 ohms C = 1 nano F. a) Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit b) Calculate the complex power on the load.
In the circuit in the figure, there is a load formed by connecting the resistor R0 between the terminals a and b and the inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volts, the phase angle θs = 0 degrees, the period is T = 200π microseconds. Since R = 300OHM and C = 1 microFa) If the load phase angle is constant θL = 60 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit.b) Calculate the average power on the load.
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). f) Suppose you know P and Q for a two-terminal element. What is the power factor of this element? When would you be ahead and when would you be behind? g) Suppose you know the equivalent resistance R and the equivalent reactance X of a two-terminal passive network. What is the power factor of this network? When would you be ahead and when would you be behind?
In the circuit in the figure, there is a load formed by connecting the resistor R0 between the terminals a and b and the inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volts, the phase angle θs = 0 degrees, the period is T = 200π microseconds. Since R = 300OHM and C = 1 microF a) If the load phase angle is constant θL = 60 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. b) Calculate the average power on the load.
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
InclassofENG100youwereaskedtoconnectacoilofresistance50Ωand inductance0.318Hwithacircuitcomprisinga75Ωresistorinserieswitha 159μFcapacitor.Andyouconnectedyourresultingcircuittoa240v,50HzAC supply.Calculate:(a)thesupplycurentofyourcircuit;(b)the circuit impedance,resistance and reactance(c)the phase-angle ofthe resulting curent,use sine as yourreference and explainyourresult.