1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?

1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3. (a) Explain the control word as per the register configuration given above.
Assume the following register contents: t0 = 0xAAAAAABA, t1 = 0x82345678 For the register values shown above, what is the value of register t2 for the following sequence of instructions? sll t2, t0, 6 or t2, t2, t1
. Flag Register is a special purpose. Name two types of registers used in 8086 microprocessor. Consider the given example and explain how over flow, carry, parity and auxiallry flag will work on these instruction. MOV AL, 50 (50 is 01010000 which is positive) MOV BL, 32 (32 is 00110010 which is positive) DD AL, BL (82 is 10000010 which is negative)
The contents of a four bit register are initially 1011.The register is shifted six times to the right, with the serial input being 101101. What are the contents of the register after each shift?
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
(i) Compute bitwise NOT A and place the result in A.(ii) Compute bitwise AND A, B and place the result in A(iii) Compute bitwise OR A, B and place the result in A(iv) Compute bitwise XOR A, B and place the result in A(v) Can PONY be used to compute ADD A, B, the 32-bit addition of registers? Please justify your answer.
How to store (1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
question1:In a memory system, data is 16-bit wide. Break the information into bytes with their addresses using little endian and big-endian methods. Starting address is F800 and the data is: E0F2 0041 question2:What acknowledgment signals are there in I2C bus?
A 4-bit universal shifting register QA, QB, QC and QD and a single serial input called SI, has two inputs so that they determine how to operate, as follows: M0M1 = 00 indicates that it should keep the value of the current outputs, M0M1 = 01 indicates that you should shift right, M0M1 = 10 indicates that you should shift left, and M0M1 = 11 indicates that you should parallel load inputs A, B, C, and D. Design a minimum circuit that implement this record and draw the final schematic diagram. Include the entire design procedure
How to build this circuit? (on Digital or Logisim) Binary-coded decimal is an alternative method of representing integers using binary. In it, each base-10 digit is represented by four bits, thus each nibble takes one of 10 values (0000 through 1001). Therefore, using BCD, 42 (decimal) is represented as 0100 0010 (binary) and 196 (decimal) is represented as 0001 1001 0110 (binary). Create a circuit in Logisim that accepts as input a pair of two-digit integers represented as BCD and outputs their sum in BCD. Any and all Digital components are fair game. You can assume that all inputs will be valid BCD-encoded numbers.
true or false ?? an even two bit parity checker will output a parity error if data A=LOW data , B=HIGH. parity bit = HIGH
Identify the contents of the registers, the memory location (C055H), and the flags as the following instructions are executed in 8085 microprocessor. A H L S Z CY M(C055H) LXIH, C055H MVI M,8AH MVI A,76H ADD M STA C055H HLT