Solve 1- 5 please with a clear understanding 2Given the Following beam in simple flexure, loaded at midspan:PSectionSpan, LD) Sketch Shear and Moment Diagrams below:VM00h3/8"A tensile test is performed on a brass specimen 3/8" in diameterusing a gage length of 2". When the load P reaches a value of 4500lb, the distance between the gage marks has increased by 0.0048".Assume that the material is loaded within its elastic range.Lo=2"bA load of mass 9072g is applied to a cantilever beam.3A circular rod is found to have a cross sectional area of 113mm²4Two samples are tested to failure in compression. A wood samplefails at a load of 18,000 lbs. A concrete sample fails at 62,000 lbs.The wood sample is a square block measuring 1.5" x 1.5" in crosssection. Te concrete sample is a cylinder with a section diameterof 4"5ConcreteWoodA) What is the maxmoment at midspanin terms of P, L, b, hB) What is the stress inthe top fibers atmidspan? SpecifyTension orCompression. Interms of P, L, b, h.C) Given the samebeam with a distributedload, what is themoment at midspan ofthe beam? In terms ofw, L, b, hA) Axial Strain at aload of 4500lb (andunits):B) What is the mod. Ofelasticity, E, of thebrass? (and units):What is the load inpounds force:What is the diameter ininches?A) Which material hasthe higher ultimatestrength? (circle one)WoodConcreteB) What is the ratio ofconcrete/wood ultimatestrength?

Answered: Image /qna-images/answer/968d78e5-9ee6-4623-afbe-a93b1cf3b701.jpg

Given the Following beam in simple flexure, loaded at midspan: P Section h Span, L D) Sketch Shear and Moment Diagrams below: VI M b A) What is the max moment at midspan in terms of P, L, b, h B) What is the stress in the top fibers at midspan? Specify Tension or Compression. In terms of P, L, b, h. C) Given the same beam with a distributed load, what is the moment at midspan of the beam? In terms of w, L, b, h

Given the Following beam in simple flexure, loaded at midspan: P Section h Span, L D) Sketch Shear and Moment Diagrams below: VI M b A) What is the max moment at midspan in terms of P, L, b, h B) What is the stress in the top fibers at midspan? Specify Tension or Compression. In terms of P, L, b, h. C) Given the same beam with a distributed load, what is the moment at midspan of the beam? In terms of w, L, b, h

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.34P: using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of...

See similar textbooks

Similar questions

A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3, Sy=128x103 mm3, d=358mm, bf=184mm, A=7,289mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 600 mm in diameter, and 5-17-mm-diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 66 MPa in the bolts? Answer must be in kN-m.
4. A steel supplier lists rectangular steel tubing having outside dimensions of 4 by 2 in.and a wall thickness of 0.109 in. What is the maximum torque that can be applied tosuch a stube if the shear stress is to be limited to 6000 psi. For this torque, computethe angle of twist of the tube over a length of 6.5 ft
A nail joint is subject to medium term tensile loading under service class 2. The joint comprises of eight 3.75 x 60 mm long round wire in single shear in C18 timber. What is the slip modulus? Question 4Answer a. 780.38 b. 550.69 c. 625.37 d. 659.19
Nicole took a steel rod, 15.08-mm in diameter, and held snugly (but without any initial stress) between rigid walls as shown in the figures. Assuming that the steel rod has a CLTE is 12.4 ×10−6mm/mm∘C and E = 200GPa. 1) Calculate the temperature drop at which the average shear stress in the 11.78-mm diameter bolt becomes 46.387MPa.2) Calculate the normal stress on the rod3) Based on figure (a). What is the average bearing stress between the washer (21.84 mm diameter) and the wall (thickness: 19.89mm) 4) What is the average bearing stress between the bolt and clevis with a thickness of 14.34mm?
A steel plate 375mm x 16mm thick is bolted by four bolts placed symmetrically to form a single lap joint. The bolts are spaced horizontally at a distance of 140mm and vertically at a distance of 150mm. If the diameter of bolt is 20 mm, calculate the design tensile strength in KN based on net section fracture considering a straight vertical path of failure Use Fy=248MPa and Fu=400MPa a) 1339.2 b) 1569.6 c)2092.8 d) 1488
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
Six 7/8-in-diameter rivets fasten the plate in Figure below to the fixed member. Determine the average shearing stress caused in each rivet by the 15 kips loads. What additional loads P can be applied before the shearing stress in any rivet exceeds 9100 psi?
A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in diameter, and four 10 mm. steel bolts on a bolt concentric bolt circle of 200 mm. in diameter. (a) Determine the torque applied (N-m) if the shearing stress is 60MPa in the bolts. (b) If the torque capacity increased to 8 kN-m, determine the number of bolts of 10 mm. diameter on the 300 mm. bolt circle of the coupling.
A rectangular beam with notches and a hole (seefigure) has dimensions h = 5.5 in., h1 = 5 in., and widthb =1.6 in. The beam is subjected to a bending momentM =130 kip-in., and the maximum allowable bendingstress in the material (steel) is σmax = 42,000 psi.(a) What is the smallest radius Rmin that should beused in the notches?(b) What is the diameter dmax of the largest hole thatshould be drilled at the midheight of the beam?
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.