Given the following measurements (in metric and English respectively) of a metal cylinder: length = 5.640 cm, 2.274 in; diameter= 2.188 cm, 0.878 in. Determine the experimental value of the conversion factor from cubic centimeters to cubic inches. [Use three (3) decimal places].

Q: The area of a round tabletop is computed from a measurement of its radius. If the fractional…

A: A= πr2

Q: You measure a certain flow rate to be Q=12.9±1.6cm3/min. What would be the uncertainty in the…

A: The given value of flow rate is, For a logarithmic value (base 10), the absolute uncertainty can be…

Q: Suppose your speedometer has an uncertainty of 4.5 km/h at a speed of 92 km/h. what is the percent…

A: An uncertainty speed of speedometer, u'=4.5 km/h   The original speed, u=92 km/h

Q: 5.6 A pipe with a 16 in. diameter carries water having a veloc- ity of 3 ft/s. What is the discharge…

A:

Q: When reading a digital device, which of the following would be an appropriate decimal place to…

A: Random error arise from the fluctuations which are most easily observed by making multiple trials of…

Q: Although aluminum foil is very thin, it does have some thickness. We cannot typically “measure” the…

A: The volume of the cuboid = length×width×height   Length and width are given but height is not given…

Q: In a Measurement ,the Expected value is 56 V and the measured value is 52 V. Find (i) Absolute error…

A: Given  Expected value. Is 56 Measured value is 52.

Q: MEASURED USING CENTIMETER RULER MEASURED USING CENTIMETER RULER   Measured Diameter d (cm) Measured…

A: Solution: Calculate the relative uncertainty in diameter for dime. ∆Uddime=0.051.76×100=2.84%…

Q: What is the approximate percent uncertainty in the measurement given   1.57 m2?

A: The given measured quantity is,

Q: (I) Express the following using the prefixes of Table 1–4: (a)1 x 106 volts,  (b) 2 x 10–6 meters,…

A: Some measurements

Q: Please explain the difference between the terms 'measurement uncertainty' (sometimes called…

A: Error:  It is the uncertainty happening in measurements. When observed value differs from true…

Q: A series of four measurements of the ratio of the circumference to diameter of a disk are made. The…

A: The result of these measurement are as below. 3.140, 3.133, 3.132, 3.133   The experimental value is…

Q: how to determine experiment density with of a zinc rod with only the mass, length and diameter, when…

A: Given: Mass of zinc rod, m = 69.5 grams length of rod, L = 34.3 cm Diameter of rod, D=19 cm To…

Q: What is fractional error or percent error?

A: Fractional error is the ratio of the value of error to the value of the quantity.

Q: Given the most probable value of a quantity to be 35.86. If the Error Ratio is 1:163, What is the…

A: Suppose quantity is E . So by error analysis  Relative error in( E )=  ∆E/E

Q: How do you determine the percentage error of a zinc rod when the experiment density is 0.0071g/cm^3…

A:

Q: An engineer reports the findings of a measurement as 321.5332 + 2.3 kg (95%). Comment of the proper…

A: The value is Expressed in one decimal digit after point.

Q: By measuring the acceleration due to gravity a student finds gA=(9.85+-0.08)m/s^2. A student B finds…

A: Note: You have posted a question with more than three subparts.  As per our policy, if nothing is…

Q: Our classroom was kept at 25.0°C during your experiment, so v is predicted to be 343 m/s. What is…

A: Given data :              Speed of sound in air ;                                          Expected…

Q: What are Personal Errors? How shall this affect the final measurements? How Shall we minimize these…

A: SOlution: To describe about personal errors and thier effect on the measurement.

Q: If x = 3.54 ± 0.02 y 8.03 ± 0.04 z = 5.02 ± 0.02, what is the absolute uncertainty in f = (x + y -…

A: A quantity can be written as x = x ± Δx  x = measured value Δx = uncertainty in meassurement

Q: Calculate the following with the correct number of sig figs. 1.5.00 + 2.1

A: Significant figures are the number of digits that contribute to the accuracy of a measurement. While…

Q: An instrument is used to determine the concentration of a chemical in water. The instrument signal…

A: Given : Relation between instrument signal "Z" and concentration of the chemical "C" Z = kC + P Z =…

Q: Do percent errors and percent difference give indications of accuracy or precision?

A: Accuracy is a measure of the degree of closeness of a measured or calculated value to its actual…

Q: An infant’s pulse rate is measured to be (130.0 + 5.0) beats/min. What is the absolute uncertainty…

A: Given that:- Infant pulse rate=(130+5) beat/min

Q: An infant’s pulse rate is measured to be 130 ± 5 beats/min. What is the percent uncertainty in this…

A: Formula for calculating percent uncertainty can be express as -  Where

Q: When measuring a shaft with a specified diameter of 0.50 ± 0.01, what minimum descrimination should…

A: Given that, A shaft with a specified diameter of 0.50 ± 0.01. We need to find the minimum…

Q: Regarding measurement error, which of the following statements is not correct? Select one: a.…

A: Option a is correct answer.     Statement a is incorrect statement as absolute error don't have plus…

Q: in the Potentiometer experiment, which of the tollowing must bo true cbout the wire on themeter…

A: in the potentiometer experiment the wire used must have uniform cross sectional area. Option A is…

Q: Determine how many sig figs are in the following values. 1. 267562

A:

Q: An infant’s pulse rate is measured to be ( 132 ± 6 ) beats/min. What is the percent uncertainty in…

A: Given Data: The pulse rate is measured as: 132±6 beats/min

Q: In a Measurement ,the Expected value is 72 V and the measured value is 63 V. Find (i) Absolute error…

A: (i) The absolute error is given by :  (ii) The relative error is given by :

Q: A certain geophysical technique determines the electrical resistivity of the ground by measuring the…

A: Uncertainties in measurement arise due to mainly three reasons, Instrument, Human and Environment…

Q: A person (he/she) measures heart rate by counting the number of beats in 30 sec. -If 45 ± 2 beats…

A:

Q: (II) What is the percent uncertainty in the measurement 5.48 ± 0.25 m?

A: The expression for the percent of uncertainty is,

Q: A quadrilateral shaped area given by the following measurements have these corresponding probable…

A: Perimeter is sum of all four sides. In summation , error is sum of numerical value of all errors.…

Q: A good-quality measuring tape can be off by 0.58 cm over a distance of 23 m. What is its percent…

A: a measuring tape can be off by 0.58 cm = (0.58 / 100) m Here, 100 cm = 1m and 1 cm = (1/100) m Total…

Q: A series of four measurements of the ratio of the circumference to diameter of a disk are made. The…

A:

Q: A cylinder was measured to have length 4.24 + 0.01 cm and diameter of the cross-sectional area 2.16…

A:

Q: A parameter x is measured with a relative uncertainty of 4 percent. If x=19.0, what is the absolute…

A: Given data:

Q: From the data obtained by a group of students below, compute the experimental densit of the material…

A: Given:- The standard density of the capper is =8.9 g/cm3  Diameter of the copper D= 3.25 cm =3.25 X…

Q: The table shows the set of five measurements recorded in a laboratory. The precision of 3rd…

A: Precision tells us to what resolution or limit, the quantity is measured by a measuring instrument…

Q: For the measurement of length: 1km ± 50m and expected value of 1100m, find the relative uncertainty.

A: Given, measurement of length, l=1km ±50 m expected value =1100km

Q: he measurement of the brass cylinder is taken. The diameter is 2.0 cm, height is 4.0 cm, and nass is…

A:

Q: How do you estimate the error of a measurement performed with a meterstick? Why?

A: An error made by using the equation of a regression line to estimate the values of the dependent…

Estimate of calculation