Given the stress-strain curves for material A and B, mark if the statement is (T)rue or (F)alse? Explain why? a) Material A is the strongest material (T) / (F) b) Material B is the most rigid material (T) / (F) c) Material A is the toughest material (T) / (F) d) Material B is the most ductile material (T) 7 (F) e) Material A is the most brittle material (T) / (F) f) Material B has the highest strain hardening (T) / (F} g) Material A is the most flexible material (T) / (F) h) Material B is the stiffest material (T)/ (F) A B C.

Given the stress-strain curves for material A and B, mark if the statement is (T)rue or (F)alse? Explain why? a) Material A is the strongest material (T) / (F) b) Material B is the most rigid material (T) / (F) c) Material A is the toughest material (T) / (F) d) Material B is the most ductile material (T) 7 (F) e) Material A is the most brittle material (T) / (F) f) Material B has the highest strain hardening (T) / (F} g) Material A is the most flexible material (T) / (F) h) Material B is the stiffest material (T)/ (F) A B C.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.5P: Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight...

See similar textbooks

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
In the case of plane stress, how can the plane-strain analysis be used?
A tensile bar is stressed to 250 N/mm2 which is beyond its elastic limit. At this stage the strain produced in the bar is observed to be 0.0014. if the modulus of elasticity of the material of the bar is 205000 N/mm2 then the elastic component of the strain is very close toa. 0.0004b. 0.0002c. 0.0001d. 0.00005 PLS EXPLAIN YOUR ANSWER THOROUGHLY
Can the normal strain on the free surface of a body be measured in aparticular direction using an electrical resistance strain gage? Give an example?
What are the two parts of strain-energy density?with
Does the normal strain depend only on the assumptions made with regardto the deformation?
Consider the tensile stress-strain diagram below. If samples 1 and 2 are different materials, which sample is tougher? A. Both samples are equally tough/ Albei monsters is ewe taai B. Sample 2 C. Sample 1
Define plane stress and plane strain, making clear which, if any, of the stresses are zero in each case.
If the material remains elastic, then the strains caused by deformation are directly related to the stress. Is it true? How?
Write out the most general expression for tension orcompression strain along a single axis resulting from all possibleapplied stresses,assuming that the material is elastically isotropic.