Given the table below and your judgement for extreme operational conditions, select polymers for the following applications respectively: a dry ice bucket (operating temperature of -78C), a teeth aligner, a hair dryer (operating temperature range of 60-80C) and a phone case. Table 15.2 Melting and Glass Transition Temperatures for Some of the More Common Polymeric Materials Material Polyethylene (low density) Polytetrafluoroethylene Polyethylene (high density) Polypropylene Nylon 6,6 Polyester (PET) Poly(vinyl chloride) Polystyrene Polycarbonate Glass Transition Temperature [°C (°F)] -110 (-165) -97 (-140) -90 (-130) -18 (0) O d. Nylon, PET, HDPE, PVC HDPE, LDPE, LDPE, PTFE e. O a. Polypropylene, PET, PTFE, Polypropylene b. PTFE, HDPE, HDPE, polypropylene O c. 57 (135) 69 (155) 87 (190) 100 (212) 150 (300) LDPE, PTFE, Nylon, polypropylene Melting Temperature [°C (°F)] 115 (240) 327 (620) 137 (279) 175 (347) 265 (510) 265 (510) 212 (415) 240 (465) 265 (510)

Q: One hundred mol/h of butane (C4H10) and 5000 mol/h of air are fed into a combustion reactor.…

A: Given details: molar flow rate of butane, m=100 mol/h molar flow rate of air,M=5000 mol/h   we need…

Q: Q.21 An aqueous sodium chloride solution (10 wt%) is fed into a single effect evaporator at a rate…

A:

Q: 100 mols per second of ammonia (NH3) is burned with 20% excess O2 based on fresh ammonia feed)…

A:

Q: A continues fractionation column, operation at atmospheric pressure, is to be designed to separate a…

A: A mixture of CS2 and CCl4 is to be separated into distillate and bottom product with the help of…

Q: Q4 Ethylene is a valuable feedstock for many chemical processes. In future years, when petroleum is…

A: Initial number of moles of ethanol = 1 mol Initial number of moles of N2 = 1 mol

Q: Calculate the enthalpy change for the reaction and the type of reaction: P406(s) + 2 02(g)----->…

A:

Q: The Bradford protein assay is a dye-binding assay based on the differential color change of a dye in…

A: A data between concentration and absorbance is given.

Q: 10-32 A 1-mm-diameter nickel wire with electrical resis- tance of 0.129 2/m is submerged…

A: Given details: Diameter of wire, D=1 mm =0.001 m electrical resistance of wire , R=0.129 ohm/m…

Q: You measure the mixing ratio of a gas to contain 15% ammonia and rest air. The required collection…

A: Ammonia is to be absorbed from the ammonia-air mixture with the help of a scrubbing liquid.

Q: Consider the following hypothetical chemical reaction: As (aq) + 4B (g) → C(s). An experimental run…

A: Given details, reaction, A+4B→C B consumed ,V=1500 mL=1.5 L P=2 atm T=50 C = 50+273 =323 K…

Q: E. coli is grown in a chemostat with a working volume of 1.0 litre. A medium containing 4 g litre¹…

A: Given data: Volume of chemostat = 1 L Initial concentration of substrate = 4 g/L Final concentration…

Q: A stock containing 1.526 kg moisture per kg dry solid is dried to 0.099 kg moisture per kg dry solid…

A:

Q: A stream containing 5.15 wt% chromium, Cr, is contained in the wastewater from a metal finishing…

A: Given that- Bypass stream is the stream passing more than 4500 kg/h. Since, bypass stream, m3= 1400…

Q: An air stream is contaminated by 100 ppm (on a molar basis) of compound X. You wish to remove…

A: C) point corresponds to the temperature of 300K and pressure of 0.0001 atm in the phase diagram…

Q: 11) An ideal monoatomic gas expands from 2.5 L at 300 K to 8.0 L at a constant pressure of 3.0 atm.…

A: Given, The constant pressure of the gas, P = 3.0 atm The initial volume of gas, V1 = 2.5 L The…

Q: A midsize steam-methane reforming plant is consuming methane at a rate of 125,000 mol/h and…

A:

Q: 6. For a given binary system at constant temperature and pressure, the molar volume (in m³/mol) is…

A:

Q: An elementary liquid phase reaction A+B>C was conducted in two continous stirred tank reactors…

A:

Q: 16. A CSTR and a PFR of equal volume are connected in series as shown below to carry out a…

A:

Q: A supercritical CO2 extraction system is being operated at 30.6 Mpa and 60◦C in the extraction…

A: Given that- For a supercritical CO2 extraction system, Operation pressure, P1=30.6 MPa =30600 kPa…

Q: Pump 10 kg H₂O(l)/s through a 5-cm ID pipe to a point 125 meters above the pipe inlet. How much…

A: given = m = 10Kg/sec Z2-Z1 = 125m also, inlet and outlet temperatures are the same hence Q and H…

Q: 4) A solution of sugar in water is to be concentrated from 4% by weight to 20% by weight. The…

A: Hi and thanks for the question. Since you have asked to solve the subparts a and b, we are solving…

Q: A 2.200-g of quinone, C6H4O2, is burned in a bomb calorimeter whose total heat capacity is 7.854…

A: Given that m =2.2 g C=7.854 KJCT1  =23.44 CT2  =30.57 C

Q: volume of the tank to store 683 kg of water

A: Given Data : Quality of wet steam, x = 0.42 Tank under pressure of , P = 15 bar Total mass of water…

Q: 3. Under constant-volume conditions of heat of combustion of glucose,C6H₁2O6, 1s 15.57 KJ/g. A…

A:

Q: A pair of concentric glass cylinders, with diameters of 1 and 1.05 cm, respectively are held…

A: Given Data Di = 1 cm = 0.01 m Do = 1.05 cm = 0.0105 m Surface Tension = 0.019 N/m Density of Oil =…

Q: 1 mol of a mixture consisting of 30% methane and 70% propane is burned in stoichiometric air.…

A:

Q: In this question, I did not understand the value of YAN+1. How was it calculated? Is it 0 or 0.02?

A: A mixture of acetone, 1,1,2-trichloroethane is contacted with a mixture of water and…

Q: Arrange the compound according to the increasing and explain why? in resilience

A: Introduction Vulcanization  is a range of processes for hardening rubbers. The term originally…

Q: 8. B. friction factor imbers 7 to 9, e given U-tube manometer, mercury was used in the manometer to…

A: Density of Hg mercury Dhg = 13600 kg/m3 Density of water Dw = 1000 kg/m3

Q: A second degree process with time delay is controlled by a closed loop control system with feedback.…

A: The closed transfer function and the value of Kc for stable operation is to be determined.

Q: Problem 1: Water at 400°C has a specific volume of 0.00700 m³/kg. Determine the pressure of the…

A: Given: The water temperature is T = 400oC = 673 K and the specific volume is v = 0.007 m3/kg The…

Q: Q.2: The combustion analysis using ORSAT apparatus, where the analysis indicated as 15% CO2, and…

A: Given data: Composition of CO2 in the dry stack gas = 15 %

Q: 1. A feed of 10,000 kg/h is 10 wt% acetic acid in water. The acetic acid will be removed using a…

A:

Q: A fuel containing 60% ethane, 20% propane, and 20% methane is burned with 30% excess air at 25°C,…

A: Note: As per our guidelines, we are supposed to solve only 3 subparts of a question. Kindly send the…

Q: Gaseous butane (CH₂(CH₂), CH₂) will react with gaseous oxygen (O₂) to produce gaseous carbon dioxide…

A:

Q: I 7-133 Consider a person who is trying to keep cool on a hot summer day by turning a fan on and…

A: given = air temp = 32^c velocity of air = 5 m/s surrounding temp = 40^c emissivity(e) = 0.9 rate of…

Q: cm Thermal conductivity: 0.53 W/cm C 8. You have been assigned to design a heat exchanger to cool ou…

A:

Q: Write and simplify the closed-system energy balance for each of the following processes, and state…

A:

Q: Butane (C4H10)(C4H10) and dry air are fed to a combustion reactor at a steady rate of 45.9 mol/s45.9…

A: Given that, The molar flow rate of butane in the feed stream nC4H10,F = 45.9 mols The molar flow…

Q: Using data from Table A-25, calculate the equilibrium constant expressed as log10K, for the…

A:

Q: A tray tower to be designed to absorb SO2 from an air stream by pure water at 293 K. The entering…

A: Sulfur dioxide is removed from the air mixture with the of liquid water in an absorption tower.

Q: d'T' dx² 'T' 9⁰. m k

A: Aim: Solve the given second order differential equations. The given equation is linear differential…

Q: There are three thermal energy reservoirs that are being used by a reversible engine, namely X,Y,…

A: Given that, An equal amount of heat is being absorbed by the engine from reservoirs X and Y Qx = Qy…

Q: the cor

A:

Q: A fuel containing 70% ethane and 25% propane is burned with dry air. All the H₂ burns to H₂O and the…

A: Basis feed=100 mol (supposed)  Given that feed has- Ethane (C2H6)=70% = 70 mol Propane (C3H8)=25%=…

Q: Aqueous hydrochloric acid (HC1) reacts with solid sodium hydroxide (NaOH) to produce aqueous sodium…

A: HCl + NaOH = NaOH + H2O Molar mass of NaOH = 40 g/mol Molar mass of HCl = 36.5 g/mol     x…

Q: A pharmaceutical plant uses an incinerator to destroy its organic solvents including heptane (C7H16)…

A: C7H16 + 11[O2 + 3.76N2] = 7CO2 + 8H2O + 41.36N2 WKT, air contains 21% O2 and 79% N2 hence ration of…

Q: 10-4 1.084 0.249 1 1 + 9 9 29- mol mol/ N (1013252) (0.416 nm)² (0.595) 1 46.07 (273 K)³/2 1 9 46.07…

A: Given equation is 10-41.084-0.249146.07+129273 K3/2146.07+129101325 Nm20.416 nm20.595   We know,  N…

Q: A second degree process with time delay is controlled by a closed loop control system with feedback.…

A: The disruptive or disturbance transfer function can be written with above given equation using…