Given two batteries: one with voltage V and internal resistance r₁; another with also voltage V and internal resistance r2. Which of the following is true if we connect them in parallel with both their positive terminals connected to each other? The total voltage will be V, while the total internal resistance is (₁-1 + √2-¹)-1. The total voltage will be 2V, while the total internal resistance is (₁) 1-1 + √₂-1)-1. The answer cannot be found on the other choices. No voltage will remain, while the total internal resistance is (₁-1 + ₂-1)-1.

Given two batteries: one with voltage V and internal resistance r₁; another with also voltage V and internal resistance r2. Which of the following is true if we connect them in parallel with both their positive terminals connected to each other? The total voltage will be V, while the total internal resistance is (₁-1 + √2-¹)-1. The total voltage will be 2V, while the total internal resistance is (₁) 1-1 + √₂-1)-1. The answer cannot be found on the other choices. No voltage will remain, while the total internal resistance is (₁-1 + ₂-1)-1.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter17: Current And Resistance

Section: Chapter Questions

Problem 10CQ: Power P0 = I0 V0 is delivered to a resistor of resistance R0. If the resistance is doubled (Rnew =...

See similar textbooks

Similar questions

Power P0 = I0 V0 is delivered to a resistor of resistance R0. If the resistance is doubled (Rnew = 2R0) while the voltage is adjusted such that the current is constant, what are the ratios (a) Pnew/P0 and (b) Vnew/V0? If, instead, the resistance is held constant while Pnew = 2P0, what are the ratios (c) Vnew/V0, and (d) Inew/I0?
If the battery in the circuit below is 3.53V, resistor R1=69.44ΩΩ, and resistor R2=61.16ΩΩ, what is the magnitude of the potential drop across resistor R2? Please give your answer in units of Volts (V).
Consider a circuit with three capacitors in parallel, where C1 = 1.50 μF, C2 = 8.50 μF, and C3 = 4.80 μF, find the equivalent capacitance.
Suppose a resistor R1 is in series with a parallel pair R2; R3. If R1 is 100, R2 is 200, and R3 is 350, what is thecurrent through R1 if the voltage is 3V?
Calculate the equivalent resistance of four resistors R1=100 ohms, R2=250 ohms, R3=350 ohms and R4=200 ohms such that R1 and R2 in parallel will be connected in series with R3 and R4 in parallel.
If two resistors with resistances R1 and R2 are connected in parallel, then the total resistance R, measured in ohms (Ω), is given by 1/R =1/R1 + 1/R2. If R1 and R2 are increasing at rates of 0.3 Ω/s and 0.2 Ω/s, respectively, how fast (in Ω/s) is R changing when R1 = 80 Ω and R2 = 100 Ω?
Consider a cylindrical ohmic wire with the following dimensions: length = 10.0 m, radius = 0.05 m. When the ends of the wire were connected to a 2.0 V voltage source, a 1.0 A current through the wire was measured. Determine the resistivity of the wire. Choices: 3.93 x10^-4 Ω-m, 1.57 x 10^-3 Ω-m, 3.14 x 10^-2 Ω-m, 3.92 x 10^-2 Ω-m, 1.57 x 10^-1 Ω-m
When is a 1.5 V AAA battery not actually a 1.5 V battery? That is, when do its terminals provide a potential difference of less than 1.5 V?
In the circuit shown in the figure, the S switch closed at t=0 and the capacitors, which are completely empty, begin to fill. Here ε=10 V, C=5 μF and R=55 Ω. What is the time constant of the circuit, τ, in units of microseconds? When t= τ, what is the total charge, in units of microcoulomb, accumulated in the capacitors?
How do you find the value of a resistance R1, in a circuit when the equivalent resistance is 40 ohms, given that: R2 = 12 ohm in series with R3 = 40 ohms whom combined are in parallel with R4 = 20 ohms, all in parallel to R1. And to find the current in each resistor, do I just apply the equation, I = V/R, given that the circuit runs on an 28 volt batt.
If a capacitor, C=30.4 μF is suddenly connected to a circuit with the total resistance of R =10.22 Ὼ in the circuit with a battery of any capacity, how much time (in microseconds) will elapse for the voltage on the capacitor to be 60 % that of the battery?
Two identical resistors of 276 Ohms are configured in parallel and connected to a 13.3V power supply. If the same two resistors are then connected in series,what should the voltage of the power supply by charged to such that the parallel and series configurations draw the same amount to power?