Answered: Given year of fill sediment =50 yr,…

Given year of fill sediment =50 yr, Increment volume = 7000 acre-ft, trap efficiency = 90% and 91% , Annual sediment trapped is إختر أحد الخيارات 130 .A O 120 .B O 140 .C O 150 .D O

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Ground Improvement

Section: Chapter Questions

Problem 11.7P

See similar textbooks

Related questions

Q: For a grit chamber, if the recommended velocity of flow is 0.2 m/s and the detention time is 2…

A: Grit chambers are long broad tanks that are designed to slow down the flow so that solids such as…

Q: Two sedimentation tanks operate in parallel. The combined flow to the two tanks is 0.1000 m3/s. The…

A: In the question, the tanks are connected in parallel. The total discharge is the sum of the…

Q: Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of…

Q: |A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in the…

A: Co-efficient of permeability(k)=4.5x10-3 cm/sec Number of flow lines=3 Number of drops=6

Q: 16. A rectangular sedimentation tank is to be designed for a flow of 20 million litre per day using…

Q: Problem 9.4: An 20 mm of average particle diameter. Taking, n-0.02, So-0.0015, z=2, and will be…

A: An unlined trapezoidal channel Manning's constant, n=0.02 Slope of channel bed, So=0.0015 Side slope…

Q: Rapid Sand Filter - Example • Determine the minimum number of rapid sand filters necessary to treat…

Q: A municipal wastewater treatment plant with average flow of 1.5 MGD and maximum flow during the day…

A: given average flow = 1.5 MGD peak factor = 2.6

Q: A rectangular sedimentation tank is to handle 10 MLD of raw water. A detention basin of width to…

A: Solution:- Given that flow raw sewage?=10 MLD…

Q: silt theory. Design an irrigation channel to carry a discharge of 14 cumecs. B. = 5.7 Assume 7 =…

Q: Refer to Problem 8.12. Given k, = 4× 10-S m/min and k, = 1 × 10-5 m/min, calculate the rate of…

A: Consider the given figure. Calculate the slope of the dam. tanα=12α=26.56°

Q: Determine the capacity of the collector for the following data, the soil type is medium(c2=0.16).the…

A: Given: Soil type is medium, c2 = 0.16 Topography is flat, c3 = 0.04 Well…

Q: Step 1 LiW: H = 10:1:3 Valome lokx1xX 3と %3D = 3ox3m3 8= 1080 mm |br Detention thme ='15 mmute aj…

Q: 8.7 A permanent surcharge of 100 kN/m is to be applied on the ground surface of the soil profile…

A: Solution: σ=σf+σs

Q: From the given information below of a const. of commercial bank building a. Tabulate the results for…

Q: Water fl ows in a brickwork rectangular channel 2 m wide,on a slope of 5 m/km. (a) Find the fl ow…

A: (a) The area of the rectangular section is calculated as, The wetted perimeter is calculated as,…

Q: 1. Design a box culvert with the following particulars: İnside dimensions: 3.5 m x 3.5 m Live load:…

A: Given : Inside dimensions: 3.5 m × 3.5 mLive load : IRC Class ADensity of soil, ρsoil = 18…

Q: A rectangular sedimentation tank has dimensional proportions of 10:1:3 (L:W:H). If sedimentation is…

Q: The following represents infiltration data; Calculate the following 1. Calculate F(t=50 min) using…

A: Step 1: Horton’s Equation, Ft =Fc + (F0-Fc ) e-kt The total infiltration- 284.99 mm (given) Solving,…

Q: 0 Ground surface 10 m 2 5.5m 3 Sheet pile 1.5 m 4 II III 5 id 6 Impermeable layer

Q: A- Proportional flow weir is used to keep constant horizontal velocity in: 1. Primary sedimentation…

A: Proportional flow weir is used to keep constant horizontal velocity in grit removal chamber.

Q: T18 Properties of soil and concrete %3D 4m = 30° Cohesion =0 Coefficient of base friction = 0. 50…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: According to the failure plane shown in figure, prove that: 1) 0 = 45 + 2) o = o'; tan?( 45 + + 2c'…

A: The stress is a quantity that differs from the amount of strain in the system and also the rigidity…

Q: 6) A rectangular settling basin with dimension (LXWXH) 50m x 25 m x 5 m used to settle particles in…

A: Given L = 50 m W = 25 m H = 5 m Detention time of 2.5 hours

Q: A soil profile is shown in Figure P3.3 along with the standardpenetration numbers in the clay layer.…

A: Over consolidation ratio: The ratio of Maximum applied effective stress at a point before and the…

Q: Ex 3 :Hw 2 Design unlined canal to carry a discharge of 1.0 m3 /s with a longitudinal slope 20cm/km…

A: Question is based on design of canal using lace's theory. Design discharge, slope, manning constant…

Q: 5. A radial flow circular sedimentation tank 22 m diameter treating 10,000 m%d of water has an…

Q: Q1#: For the concrete Dam shown in figure, determine the total average seepage for the given…

A: To find total seepage

Q: A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m/hr.…

A: Solution; Given that; Diameter of Central chamber(d)=4 m The flow rate of water(Q)=75 m3/h Detention…

Q: During normal operation, both chambers would be used. Each chamber is to be a rectangular tank with…

Q: A 1.5 inch crushed stone drain material has an estimated K= 1000 m/day, and porosity n= 0.38. If the…

A: Please find attached solution below

Q: A rectangular sedimentation tank is designed with a depth of 3.5 m and a detention time of 1 h. Is…

A: Solution Given Data Depth of tank= 3.5 m Detention time (td)= 1 hr G=2.65

Q: pesign a rectangular sedimentation tank to treat 120000 m3/day flows. ssume the SOR=30 m/day, L= 32…

A: Sedimentation tank is designed for the removal of suspended particles which get settle in this tank.

Q: Ex 11-4: calculate the seepage losses for one kilometer of canal carry 14 m3/sec using the three…

A: Seepage loss may be defined as the infiltration downward and lateral movement of water into soil…

Q: rectang mediah particle discha Suspended load is 2.8 mm. Use channel conveyance factor of 600 and u…

A: Note: As per the guidelines only the first three parts is being solved Critical Flow velocity: A…

Q: b. 0.22 A the vod ranwe 6. Nne d eD c. 1.49 8. In a consolidation theory, the soil assumed to be: a.…

Q: Q5) Despite the additional cost, the lift irrigation systems are used in the deficit of surface…

A: Qno 5 . The statement is TRUE AS , lift irrigation system is system where water is transported by…

Q: For grit chamber, if the recommended velocity of flow is 0.2 m/sec and detention period is 2…

A: Calculate the length of the grid tank by using the formula length of the tank= velocity…

Q: In a 10 m side square shaped sedimentation tank, the flow rate is 100 cum/h, and if the ater is 2 m,…

A: Given data : Flow rate (Q)=100 m3/hr depth of water =2 m

Q: Q.2: A WTP is to be treated 3800 m'/day is design with rectangular sedimentation tank at detention…

Q: A hydraulic jump is formed in a 2 m wide rectangular channel which is horizontal and frictionless.…

Q: Mass curve of infiltration for particular soil -0.25t + condition is given by F₁ = 0.5t -6e р 8…

A: given- mass curve Fp=0.5t-6e-0.25t+8It is required to find infiltration capacity in mm/hr at time…

Q: r. min ce of 1.5 m is to be made for sediment, overflow

Q: A steep rectangular channel is to carry flow rate of 1.90 m3/s wirh a slope of 0.01 and roughness…

Q: A masonry dam has a trapezoidal cross section, 25 m high, crest width of 3 m and base length 18 m.…

Q: To provide safety against piping failure with a factor of safety 5 for a hydraulic structure what…

A: Given data- FOS=5 Sp. gravity (G) = 2.5 Porosity (n) = 0.4 To find- Maximum permissible exit…

Q: wo rectangular settling tanks are each 6 m (20 ft) wide, 24 m (80 ft) long, and 2.7 m (9 ft) deep.…

A: 1. Find Overflow rate : Vo Vo =QArea=QL * W Where ; Q = Flow = 1900 m3 / 12hr = 158.33 m3 / hr L…

Q: In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the…

Q: Ihe excavation has to be kept dry. Determine the flow rate (q) nto the

A: Given k=2×10-5,slope=1V:1.2H excavated area (A)=a+b2×y3 where a=8m,b=12.8m,y=depth of excavation

Concept explainers

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.

Question

Find the question, thanx.

Given year of fill sediment =50 yr, Increment
volume = 7000 acre-ft, trap efficiency = 90%
and 91% , Annual sediment trapped is
إختر أحد الخيارات:
130 .A O
120 .B O
140 .C O
150 .D O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular sedimentation tank is designed with a depth of 3.5 mand a detention time of 1 h. Is the design suffcient to achieve complete removal of particles with a diameter of 0.01 mm? Specifc gravity of the particles is 2.65. The fow rate and temperature of waterare 10,000 m3/d and 20°C, respectively. At 20°C, density of water is998 kg/m3 and dynamic viscosity of water is 10–3 kg/m·s. State anyassumptions you make to calculate your results.
The diagram of a sand drain is shown in Figure 7.32. If rw = 0.3m, de = 6m,cv = cvr = 0.28 m2/mo, and H = 8.4 m, determine the degree of consolidationcaused only by the sand drain after 7 months of surcharge application.
A rectangular sedimentation tank has dimensional proportions of 10:1:3 (L:W:H). If sedimentation is done in batch, the tank can cater 1080 m^3 in one hour, while the detention time for a continuous settling is 15 minutes on the same tank. a) During batch sedimentation, how many batches is done in an hour? b) Solve the dimensions of the tank. c) If the critical settling velocity is 0.003m/s, how many percent of the solids will be settled down? d) If the influent has a solids concentration of 230 mg/L and the effluent is 90% of the influent, compute the solids concentrations both at the underflow and the overflow. e) Determine the filter area if the filter loading rate is 2.3 gal/d.ft. ANSWER D AND E I PROVIDED SOME INFORMATION THANK YOU!
A rectangular sedimentation tank has dimensional proportions of 10:1:3 (L:W:H). If sedimentation is done in batch, the tank can cater 1080 m^3 in one hour, while the detention time for a continuous settling is 15 minutes on the same tank. a) During batch sedimentation, how many batches is done in an hour? b) Solve the dimensions of the tank. c) If the critical settling velocity is 0.003m/s, how many percent of the solids will be settled down? d) If the influent has a solids concentration of 230 mg/L and the effluent is 90% of the influent, compute the solids concentrations both at the underflow and the overflow. e) Determine the filter area if the filter loading rate is 2.3 gal/d.ft.
Question # 3 (b): Design a grit chamber for population 80000 with water consumption of 200 LPCD, with maximum flow of 2.5 times of average flow, and horizontal velocity of 2.0m/s and detention time of one minute. Subject: Environmental Engineering
A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m/hr. raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank 2) Weir loading in m/m.d. pi g/cc, and u 1.3 c.p. 3) Diameter of the smallest settling particle is to be removed, if v=1.2 m/hr, p2 g/cc,
5. The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. Estimate the coefficient of permeability at a void ratio of 0.48. Using Casagandre equation Using Kozeny-Carman equation Find the difference in the rate of flow using the results of “a” and “b” if i = 0.70 and A = 0.6 m2.
Design a circular sedimentation tank to treat 2500 m3 of raw water per day. The retention period assumed to be 2.8 hours. The process is coagulated sedimentation, assume the flow depth=2.8 m.
two sedimentation tanks operate in parallel. The combined flow to the two tanks is .1 m^3/s. the depth of each tank is 2 m and each has a detention time of 4 h. what is the surface area of each tank and what is the overflow rate of each tank in m^3/d*m^2? Please don't provide handwritten solution
The diagram of a sand drain is shown in Figures 16.21 and 16.22. Given: rw = 0.25 m, rs = 0.35 m, de = 4.5 m, Cv = Cvr = 0.3 m2/month, kh/ks = 2, and Hc = 9 m.Determine:a. The degree of consolidation for the clay layer caused only by the sand drains after six months of surcharge applicationb. The degree of consolidation for the clay layer that is caused by the combination of vertical drainage (drained on top and bottom) and radial drainage after six months of the application of surcharge. Assume that the surcharge is applied instantaneously.
Sedimentation is the process of allowing particles in suspension in water to settle out of the suspension under the effect of gravity. A water treatment plant has four clarifiers treating 1.5 MGD of water. Each clarifier is 4.88 m wide, 24.4 m long, and 4.57 m deep. Determine the following: (i) The detention time (ii) The overflow rate marks (iii) The horizontal velocity (iv) The weir loading rate assuming the weir length is 2.5 times the basin width.
Design an irmigation channel to carry 45 cumecs of discharge. Slope is I in 3700. Lacey's Silt factor is 0.9. Side siope is 12:1. Use Lacey s method