glass container with pervious bottom containing fine sand in loose state (void ratio = 0.8) is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. If the specific gravity of sand particles = 2.65, area of cross-section of sand sample= 10 cm2 and height of sample = 10 cm, compute the seepage force in N acting from below. a. 9.17.

glass container with pervious bottom containing fine sand in loose state (void ratio = 0.8) is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. If the specific gravity of sand particles = 2.65, area of cross-section of sand sample= 10 cm2 and height of sample = 10 cm, compute the seepage force in N acting from below. a. 9.17.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.3P

See similar textbooks

Similar questions

A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
A glass container with pervious bottom containing fine sand in loose state (void ratio = 0.8) is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. If the specific gravity of sand particles = 2.65, area of cross-section of sand sample= 10 cm2 and height of sample = 10 cm, compute the head of water in cm required to cause quicksand condition. a.9.17 b.0.45 c.7.29 d.0.9
The figure shows a layer of granular soil in a tank with an upward seepage by applying water through the valve at the bottom of the tank. The loss of head caused by upward seepage between the levels of A and B is 0.71m. The void ratio of the soil is 0.511 ,its specific gravity is 2.719, h1=0.99m, h2=2.06m, h3=2.91m. 1. Compute the effective stress at C in kPa. 2. .Compute the critical hydraulic gradient. X IN FIGURE IS 1 = 0.71m
11. Consider the downward flow of water through a layer of sand in the tank shown. (see picture below) Void ratio of the soil = 0.52 Specific Gravity = 2.70 Compute the value of h1. (Answer: 0.436) Compute the effective stress at A. (Answer: 17.44 kPa) Compute the effective stress at B. (Answer: 31.98 kPa) Compute the seepage force per unit volume. (Answer: 3.57 kN/m3)
The soil profile at a site consists of 5 m sand underlain by clay layer. The ground water table is 2 m below the ground surface. Average void ratio of sand is 0.52. Water content of clay is 42% and degree of saturation of sand above water table is 37%.Assume specific gravity of sand and clay is 2.65. 1. Compute the unit weight of clay. a. 19.82 kN/m³ b. 17.47 kN/m³ c. 18.62 kN/m³ d. 16.20 kN/m³ 2. Compute the total pressure 10 m below the ground surface. a. 185.41 kPa b. 160.25 kPa c. 140.53 kPa d. 153.62 kPa 3. Compute the effective pressure 10 m below the ground surface. a. 106.94 kPa b. 96.52 kPa c. 115.62 kPa d. 108.36 kPa
Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 × 10^–2 mm/s. The thickness of the sample is 120mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the middle of the sample. a. 364 b. 910 c. 182 d. 728
A soil profile consists of 2m of sand (γ=18kN/m³, kv=4 x 10-2m/day) over 3m of silt (γ=17kN/m³, kv=1 x 10-2m/day) over 2m of silt (γ=16kN/m³, kv=5 x 10-4m/day) over gravel. The water table is 0.5m below the ground surface. A piezometer placed at the top of the gravel layer measures a porewater pressure of 42kPa. Assuming a one-dimensional flow condition in the vertical direction, compute the flow rate in m³/day/m². Also compute, atmiddepth of the clay layer, the porewater pressure, total vertical stress, and effective vertical stress.
A soil profile is shown in Figure 7.28. An embankment load of 500 kg/cm² is placed on the ground surface. Define the following: a. How much water will rise in the pizometer immediately after applying the load. b. What is the degree of consolidation at A if h = 26 ft. c. Determine the magnitude of h if the degree of consolidation at point A is 50%. And Draw the curve NB: part A Assume that the increase in pore water pressure is uniform over the entire depth of very clayey having a thickness of 10 ft.
A uniform soil deposit has a void ratio 0.6 and specific gravity of 2.65. The natural ground water is at 2.5 m below natural ground level. Due to capillary moisture, the average degree of saturation above ground water table is 50%. Determine effective pressure in kPa at a depth of 6 m. a. 46.40 b. 323.9 c. 80.66 d. 117.9
For a falling head laboratory test, the following are the given values:• Length of soil specimen = 210.00 mm• Initial head = 523.00 mm• Final head = 297.00 mm• Duration of test = 3.50 mins• Area of standpipe = 42.0 sq.mm• Area of specimen = 1050.00 sq.mmA. Compute for the hydraulic conductivity of the soil in cm/sec.B. Determine the seepage velocity if n=0.35C. Determine the head difference at t = 120 sec
A soil profi le consists of a clay layer underlain by a sandlayer, as shown in Figure P7.17. If a tube is inserted intothe bottom sand layer and the water level rises to 1 mabove the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. IfKo is 0.5, determine the lateral effective and lateral totalstresses at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stressthere to be zero?
The sand layer shown is 2.5m thick. Beneath the sand layer is a 1.8m thick clay layer, underneath the clay layer is a solid rock. Water table is at depth of 0.9 m below the ground surface. SAND: Ymoist= 23KN/m3 ; Ysat= 21KN/m3 CLAY: Ysat= 23 KN/m3 ; LL= 42% e=0.7 A.) Compute the overburden pressure at mid-clay layer. B.) Find the maximum surface pressure without exceeding a 139.5mm settlement in clay layer if it is assumed to be normally consolidated. C.) If surface pressure is 70kpa and pre-consolidation pressure is 80kpa, find the settlement in clay layer.