The velocity of a falling parachutist can be computed bygmv (t) = (1 - e-(clm))Use a first-order error analysis to estimate the error of vat t= 6 if g=9.81, m= 50 ± 2.5, and c= 12.5 ± 1.5.The error of vist[m/s.

Answered: Image /qna-images/answer/a9937335-e9be-4ad0-8b8a-4c1db405c9c8.jpg

Answered: gm (t) = (1-e-(cm)t) se a first-order…

Engineering

Mechanical Engineering

gm (t) = (1-e-(cm)t) se a first-order error analysis to estimate the The error of vist m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

From the following test data estimate the values of Ks and Kefor the filter drag model. Limestone dust loading = 1.0g/m3 Fabric area = 1.00m2 Air flow rate = 0.8m3/min Time min 5 10 15 20 25 30 Filter ∆P, Pa 330 490 550 600 640 700 Give your answers in units of (Pa-min-m)/g and (Pa-min)/m respectively
The speed of sound traveling through the sea is a function of temperature, salinity, and pressure. It is modeled by the function C = 1449.2 + 4.67T -0.055T² +0.00029T³ + (1.34-0.01T) (S-35) + 0.016D where C is the speed of sound (in meters per second), T is the temperature (in degrees Celsius), S is the salinity (the concentration of salts in parts per thousand, which means grams of dissolved solids per 1000 grams of water), and D is the depth below the sea surface, in meters. Calculate the following (Check attached image d3) when T = 10 °C, S = 35 parts per thousand, and D = 100 m. Explain the physical meaning of these derivatives.
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:
A fire hose has an inside diameter of 6.5 cm. Suppose such a hose carries a water flow of 40.5 L/s starting at a gauge pressure of 1.68 × 106 N/m2 . The hose discharges through a nozzle having an inside diameter of 3.4 cm. Take the viscosity of water to be 1.005 × 10-3 (N/m2)⋅s dh = 6.5 cmdn = 3.4 cmP = 1.68 × 106 N/m2Q = 40.5 L/s a. the Reynolds number, NR, for flow in the fire hose to show that the flow must be turbulent, with NR≥ 3000. b. Calculate the Reynolds number, NR, for flow in the fire hose and nozzle to show that the flow must be turbulent, with NR≥ 3000.
An automotive engineer is testing how quickly a newly designed sports car accelerates from rest. He has collected data giving the velocity V, in miles per hour, as a function of time t, in seconds, since the car was at rest. Below is a table giving a portion of his data. Time (t) Velocity (V) 2.0 28.4 2.5 33.9 3.0 39.4 3.5 44.9 (a) By calculating differences, show that the data in this table can be modeled by a linear function. Time 2.0 to 2.5 2.5 to 3.0 3.0 to 3.5 Change in t Change in V (b) What is the slope for the linear function modeling velocity as a function of time? mph per secExplain in practical terms the meaning of the slope. This means that, after every second, the car will be going miles per hour faster. This says that the acceleration is ---Select--- varying constant . (c) Use the data in the table to find the formula for velocity V as a linear function of time t that is valid over the time period covered in the table.V =…
The heat transfer between a solid body and a fluid medium is determined by the equation Q=h·A·(Ts-Tf). Here; Q is the amount of heat transferred, h is the heat transfer coefficient, A is the heat transfer surface area, Ts is the temperature of the surface and Tf is the temperature of the fluid. These parameters were measured as h=250±1.75 W/m2ºC, A=20±0.75 m2, Ts =100±0.75ºC and Tf =25±0.75ºC, including error levels. What is the total uncertainty in the amount of heat transferred, in ±%? a. 3.98 b. 4.07 c. 2.73 d. 2.95 e. 3.88
the following data is obtained for the velocity of a vehicle during a crash test: t(ms) v(mph) 0 30 10 29.5 20 28 30 23 40 10 50 5 60 2 70 0.5 80 0 if the vehicle's weight is 2,400 lb, approximate the force f in lb acting on the vehicle 40ms after the crash. the force can be calculated by F=m(dv/dt) , and the mass of the car m is 2400/32.2 slug. note that 1 ms=10^-3 s and 1 mile = 5,280 ft. convert t to secons and mph to fps. use 1st order forward, backward, and centered difference and apply Richardson's approximation. use h1=0.02 and h2-0.01s.Show detailed solution. Thanks!
Air flows at 20 oC through a 6 cm pipe. A square edged orifice plate with the diameter ratio β=0.4 , is chosen to meter the flow rate. A pressure drop of 250 cm H2O is measured at the flange taps with an upstream pressure of 93.7 kPa absolute. Take discharge coefficient ,C, as 0.60±1%. Assume that dimensions are known to within 0.025 mm, the systematic uncertainty in pressure is 0.25 cm H2O, and the pressure drop shows a standard deviation of 0.5 cm H2O in 20 readings. Upstream pressure is constant. In the flow measurement , determine the followings : a) The flow rate b) The systematic uncertainty c) The random uncertainty d) The total uncertainty
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V,pressure difference P, fluid density  and viscosity .a) (15P) Determine dimensionless  groups.b) (20P) A test is to be performed for a large pump that delivers 1.5 m3/s of water from 40 cmdiameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impelleris to be used. What flow rate should be used and what would be the pressure rise in model pump
A small wind turbine is tested in a wind tunnel using the following model parameters: ρ = 1.2 kg/m3 , µ = 1.81x10-5 Ns/m2 , v = 12 m/s, A = 0.03 m2 and Cp is measured as 0.42. Assuming dynamic similarity exists, calculate the power output of a full-size turbine of diameter 60 m operating in air of density 1.3 kg/m3 and viscosity µ = 1.73x10-5 Ns/m2 with wind speeds of 15 m/s
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V, pressure difference DP, fluid density r and viscosity m. a)Determine dimensionless P groups. b)A test is to be performed for a large pump that delivers 1.5 m3 /s of water from 40 cm diameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impeller is to be used. What flow rate should be used and what would be the pressure rise in model pump. Note: The model fluid is water at same temperature as the water in the prototype.
Problem statement : A simple flow-measurement device for streams and channels is a notch, of angle α, cut into the side of a dam, as shown in Fig. P5.69. The volume flow Q depends only on α, the acceleration of gravity g, and the height δ of the upstream water surface above the notch vertex. Tests of a model notch, of angle α = 55°, yield the following flow rate data: δ, cm: 10 20 30 40 Q, m3/h: 8 47 126 263 Part (A) - Find a dimensionless correlation for the data. (b) Use the model data to predict the flow rate of a prototype notch, also of angle α = 55°, when the upstream height δ is 3.2 m.