Homework Help is Here – Start Your Trial Now!
Science
Physics
> Bing Inbox (19) - mwboutin@gma x Uh-oh! There's a problem wit × A steel wheel is mounted on OSu Written HW 07 Microsoft Word - HW 07.doc X O File | C:/Users/mwbou/Downloads/Written%20HW%2007%20(1).pdf Microsoft Word - HW 07.docx 5/5 9 cm 2 cm 2.5 cm Il cm 7 cm 11. A steel wheel is mounted on a frictionless bearing as shown in the left figure above. A cross sectional diagram of the wheel is shown in the right figure below. A 2 m length of chord is carefully wound around the rum of the wheel. The chord is then pulled with a constant force of 27 N until the chord has completely unwound from the wheel. a) Determine the moment of inertia of the wheel. b) Determine how much work is done to get the wheel spinning (just after the chord is free of the wheel) and how this compares to the final kinetic energy of the spinning wheel? Note that the density, p, of the steel is 7.874 g/cm³. Some hints that might help in working this problem: Although we're not told the what the mass of the wheel is, we are given the density of the steel out of which it is made. Note that mass the mass of an object is the product of is density and its volume: m = pV . As can be seen in the cross sectional diagram above, this is not a simple solid wheel. Recall that I- Σm.y =ΣL. The wheel obviously has a hole in its center so it can be mounted on an axle. However, when the wheel is spinning, the hole is filled with the matter making up the axle. If we assume the axle is made of steel with the same density as the wheel, we can consider it part of the wheel and treat the wheel as if it didn't have a hole in its center when we're trying to find its Moment of Inertia. We might need to find the total angle, AO, through which the wheel turns as the chord is being pulled. This might be useful, for example, if we want to use any of the kinematic equations for ...

> Bing Inbox (19) - mwboutin@gma x Uh-oh! There's a problem wit × A steel wheel is mounted on OSu Written HW 07 Microsoft Word - HW 07.doc X O File | C:/Users/mwbou/Downloads/Written%20HW%2007%20(1).pdf Microsoft Word - HW 07.docx 5/5 9 cm 2 cm 2.5 cm Il cm 7 cm 11. A steel wheel is mounted on a frictionless bearing as shown in the left figure above. A cross sectional diagram of the wheel is shown in the right figure below. A 2 m length of chord is carefully wound around the rum of the wheel. The chord is then pulled with a constant force of 27 N until the chord has completely unwound from the wheel. a) Determine the moment of inertia of the wheel. b) Determine how much work is done to get the wheel spinning (just after the chord is free of the wheel) and how this compares to the final kinetic energy of the spinning wheel? Note that the density, p, of the steel is 7.874 g/cm³. Some hints that might help in working this problem: Although we're not told the what the mass of the wheel is, we are given the density of the steel out of which it is made. Note that mass the mass of an object is the product of is density and its volume: m = pV . As can be seen in the cross sectional diagram above, this is not a simple solid wheel. Recall that I- Σm.y =ΣL. The wheel obviously has a hole in its center so it can be mounted on an axle. However, when the wheel is spinning, the hole is filled with the matter making up the axle. If we assume the axle is made of steel with the same density as the wheel, we can consider it part of the wheel and treat the wheel as if it didn't have a hole in its center when we're trying to find its Moment of Inertia. We might need to find the total angle, AO, through which the wheel turns as the chord is being pulled. This might be useful, for example, if we want to use any of the kinematic equations for ...

College Physics
College Physics
1st Edition
ISBN:9781938168000
Author:Paul Peter Urone, Roger Hinrichs
Publisher:Paul Peter Urone, Roger Hinrichs
Chapter34: Frontiers Of Physics
Section: Chapter Questions
Problem 22CQ: Must a complex system be adaptive to be of interest in the field of complexity? Give an example to...
See similar textbooks
icon
Related questions
Question
100%
> Bing Inbox (19) - mwboutin@gma x Uh-oh! There's a problem wit × A steel wheel is mounted on OSu Written HW 07 Microsoft Word - HW 07.doc X O File | C:/Users/mwbou/Downloads/Written%20HW%2007%20(1).pdf Microsoft Word - HW 07.docx 5/5 9 cm 2 cm 2.5 cm Il cm 7 cm 11. A steel wheel is mounted on a frictionless bearing as shown in the left figure above. A cross sectional diagram of the wheel is shown in the right figure below. A 2 m length of chord is carefully wound around the rum of the wheel. The chord is then pulled with a constant force of 27 N until the chord has completely unwound from the wheel. a) Determine the moment of inertia of the wheel. b) Determine how much work is done to get the wheel spinning (just after the chord is free of the wheel) and how this compares to the final kinetic energy of the spinning wheel? Note that the density, p, of the steel is 7.874 g/cm³. Some hints that might help in working this problem: Although we're not told the what the mass of the wheel is, we are given the density of the steel out of which it is made. Note that mass the mass of an object is the product of is density and its volume: m = pV . As can be seen in the cross sectional diagram above, this is not a simple solid wheel. Recall that I- Σm.y =ΣL. The wheel obviously has a hole in its center so it can be mounted on an axle. However, when the wheel is spinning, the hole is filled with the matter making up the axle. If we assume the axle is made of steel with the same density as the wheel, we can consider it part of the wheel and treat the wheel as if it didn't have a hole in its center when we're trying to find its Moment of Inertia. We might need to find the total angle, AO, through which the wheel turns as the chord is being pulled. This might be useful, for example, if we want to use any of the kinematic equations for ...
Transcribed Image Text:> Bing Inbox (19) - mwboutin@gma x Uh-oh! There's a problem wit × A steel wheel is mounted on OSu Written HW 07 Microsoft Word - HW 07.doc X O File | C:/Users/mwbou/Downloads/Written%20HW%2007%20(1).pdf Microsoft Word - HW 07.docx 5/5 9 cm 2 cm 2.5 cm Il cm 7 cm 11. A steel wheel is mounted on a frictionless bearing as shown in the left figure above. A cross sectional diagram of the wheel is shown in the right figure below. A 2 m length of chord is carefully wound around the rum of the wheel. The chord is then pulled with a constant force of 27 N until the chord has completely unwound from the wheel. a) Determine the moment of inertia of the wheel. b) Determine how much work is done to get the wheel spinning (just after the chord is free of the wheel) and how this compares to the final kinetic energy of the spinning wheel? Note that the density, p, of the steel is 7.874 g/cm³. Some hints that might help in working this problem: Although we're not told the what the mass of the wheel is, we are given the density of the steel out of which it is made. Note that mass the mass of an object is the product of is density and its volume: m = pV . As can be seen in the cross sectional diagram above, this is not a simple solid wheel. Recall that I- Σm.y =ΣL. The wheel obviously has a hole in its center so it can be mounted on an axle. However, when the wheel is spinning, the hole is filled with the matter making up the axle. If we assume the axle is made of steel with the same density as the wheel, we can consider it part of the wheel and treat the wheel as if it didn't have a hole in its center when we're trying to find its Moment of Inertia. We might need to find the total angle, AO, through which the wheel turns as the chord is being pulled. This might be useful, for example, if we want to use any of the kinematic equations for ...
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 4 steps with 6 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Recommended textbooks for you
College Physics
College Physics
Physics
ISBN:
9781938168000
Author:
Paul Peter Urone, Roger Hinrichs
Publisher:
OpenStax College
SEE MORE TEXTBOOKS