H 800 N 3 m 30% G F E B 3 m 3 m Figure ZF - 19 3 m D F E 4 m B C D 700 N -2m 2 m 2 m 500 N Figure ZF-20

Q: Part (f) Determine the torque applied on the bolt by F4 in terms of the variables and angles given…

A:

Q: Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force F1…

A: Given:F1=2170 NF2=1240 NR=3100 N

Q: In figure 3, small piston {1} with face cross sectional area of 0.3 m2 received 9 kN force and…

A:

Q: A block-and-tackle pulley hoist is suspended in a warehouse by ropes of lengths 2 m and 3 m. The…

A:

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: Problem 6: Values: A = 13 lb 0₁ = 20° 0₂ = 60° Use the figure shown on the right to complete the…

A:

Q: Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force…

A: (a) To find: The angle θ made by force F1. Given: The force is F1=2170 N. The force is F2=1240 N.…

Q: 2. Three bars, hinged at A and D and pinned at B and C as shown in Figure 1-60, form a four link…

A: Given   Force, F = 20 kN      Angle = 45o Find   Another force, P

Q: What would be the resultant force F of the triangular distributed load and its location 'd' measured…

A:

Q: 1- Determine the resultant of the forces which shown in figure pila a F= 300 lb F-150 lb 37 55 13 Fy…

A:

Q: The weight of a crate is 391 newtons. Find the tension in each of the supporting cables shown in the…

A: Given, w=391 N The coordinates of the points, A0 cm, 0 cm, -115 cmB0 cm, 70 cm, 0 cmC-60 cm, 0 cm, 0…

Q: Add the force vectors in the figure by components.

A: Given Data

Q: Determine the resultant force of the concurrent force system shown in Figure 1-32. 190 kN 70 kN 60…

A: According to the details provided in the question, we need to calculate the resultant.

Q: In the motion on inclined plane, the frictional force is directly proportional to reaction force…

A:

Q: Assume that the factor of safety with respect to buckling is 2.0 and the column is made of Steel…

A: Given: F.O.S = 2.0  L2 = 2 m For A992 Structural steel, Young's modulus is E = 200 GPa = 200 x 109…

Q: In the figure below, the masses of each object are: m₁ = 2.00 kg, m₂ = 2.00 kg, m3 = 3.00 kg. The…

A: The masses are the dimesnion are .

Q: Looking for a handwritten solution. Include diagram and explanation. No gpt

A:

Q: Question 33 a = 1.2 m b = 1.8 m C = 4 m Force AB = 500 Newtons B FAB Find the x-component of Force…

A:

Q: 2. The crate weighs 450 kg and is supported by three cables as shown in the figure 2m below. 1m a.…

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: If P₁= 330 lb, P2 = 230 lb, P3 = 330 lb, and dc=8 ft, determine the reaction at A and E. (Round the…

A:

Q: For the following figure, draw a kinematic diagram for each identifying the point of interest. From…

A:

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: 1. Note: for part a), you can do this without a calculator; it might be easier to work out the…

A:

Q: Q1-1) See Figure 1, classify each of the structures as statically determinate, statically…

A:

Q: 1. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram…

A: As meter stick is balanced when fulcrum is at 49.7 cm, this distance is the center of gravity (G) of…

Q: 3 - Which of the following statements about forces is false? A) The intensity of an equivalent…

A: Answer - E) The unit of the distributed load is shown as force times length The unit of distributed…

Q: 1. The five forces shown in Figure 1-59 are in equilibrium. Compute the values of P and F. 20 KN 60°…

A: Given data: F1=20 kNF2=30 kNF3=40 kN Need to determine the values of forces P and F.

Q: 12. Draw the SFD and BMD for Figure 7 on the axes provided. Be sure to label the coordinates for the…

A:

Q: Q2/scale the Rhombus defined by the points p1=( 3,1), p23(5,3), p3=(3,5) & p4=(1,3) by a scale…

A: Given P1 = 3, 1 P2 = 5, 3 P3 = 3, 5 P4 = 1, 3 Scale factor ½ To find Rhombus with scaled factor ½

Q: Q1: Find the result of the system of converging forces in Figure (1).

A:

Q: 600 lb FOR -6 ft -6 ft 7200 lb-ft 12 ft 150 lb/ft B

A:

Q: Given the diagram below, determine the following: 3 m 2 m 2m Im im-1.5m. 1.5m 15m 3 kN 3.m 2m 4 kN…

A: Position vector is obtained by subtracting the head co-ordinates of a vector from its tail…

Q: Find the vertical force component for the figure 800 N y 50°

A: Given data :-  Force F = 800 N  Theta = 50°  Find :-  Vertical component = ?

Q: 3 kN ers One ers 3 m 1 m C D 2 m 4 kN - 3 m 2 m E 2 kN -3 m 2 m B A

A: Two Force Member: If the member has pin or hinged connection at two ends and has not external load…

Q: For the figure shown if the tension in rope AD is 180 lb find the angle between AD and AB, and then…

A:

Q: 3 in axle tire A B lugwrench

A: Given:The length of the lug wrench, The diameter of the wrench, The shear yield stress,