H.W: In the pipe systems show, find the distribution of flow, with a friction factor of 0.0163. Assume that minor losses can be neglected. If the pressure at first point (Q in =1000 kPa, then find the pressure at point A 20 mmin 5m/min 1000 m 405mm 300m 305 mm 300m 1000m 500m 10 mYmin 106 706m 205 mm

H.W: In the pipe systems show, find the distribution of flow, with a friction factor of 0.0163. Assume that minor losses can be neglected. If the pressure at first point (Q in =1000 kPa, then find the pressure at point A 20 mmin 5m/min 1000 m 405mm 300m 305 mm 300m 1000m 500m 10 mYmin 106 706m 205 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a diameter of150mm. Determine the head loss due to friction using Manning’s formula with n = 0.012.
*continuity eqn + Bernoulli’s Eqn. *check that flow after the sluice is supercritical *if supercritical, find conjugate depth of hydraulic jump *find velocities at different locations *force on the blocks = difference in hydrostatic pressure forces + difference in dynamic impact forces
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?
Hydraulic structure Q.2: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the canal-52.2m, crest level of the regulator=52.8m, upstream water level-54.2m, downstream water level=53.9m. The dimension of gates= (2.5x3)m and the thickness of the piers is 0.9m. Neglect the velocity head and use coefficients of discharge= 0.8 and 0.577. Determine the water way of the regulator
1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.