H.W.1/ Design the overflow-spillway having a vertical upstream face and a crest length of 260 ft. the design discharge is 76000 cfs. The upstream water surface at design discharge is at El. 1000 ft and the average channel floor is at El. 885 ft. the slop of downstream is 0.8H:1V, cd-2.2? Assume pointed pier, around abutment and No. of piers 3. Assume the pier width= 8 ft

H.W.1/ Design the overflow-spillway having a vertical upstream face and a crest length of 260 ft. the design discharge is 76000 cfs. The upstream water surface at design discharge is at El. 1000 ft and the average channel floor is at El. 885 ft. the slop of downstream is 0.8H:1V, cd-2.2? Assume pointed pier, around abutment and No. of piers 3. Assume the pier width= 8 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular flume of planned timber (n = 0.017) 22 ft. Wide, 950 ft. Long, with horizontal bed leads from a reservoir in which the still-water surface is 8.5 ft. Above the flume bed. Assume that the depth of the downstream end of the flume is fixed at 5.5 ft. by some control section downstream. Allowing an entrance loss of 0.18 times the velocity head, find the flow rate in the flume using one reach.
A trapezoidal channel with a bottom width of 5m and side slope of 1V:2H is constructed to convey a steady discharge to a hydropower installation. This is made up of concrete with a Manning's n = 0.016 and bed slope of 3V:2000H. a. Determine the discharge and velocity if the discharge has a 2m-depth of water? b. Calculate the depth if discharge is 35m³/s? c. As shown below, when flooded, the flow goes over the top of the channel. If the flood channels are 10 m. wide and with side slopes of 1V:3H, and roughness is n=0.035, what is the discharge for a flood level of 4m?
A 5ft x 5ft with a 45?o beveled-edge entrance reinforced concrete box culvert is to be specified for a new roadway crossing to convey a 50-year peak discharge of 300 ??3???ft3sec. The site conditions include: Stream bed elevation at culvert entrance is 100 ft. Natural stream bed slope is 0.02. Tailwater depth is 4.0 ft. Approximate culvert length is 250 ft. Shoulder elevation is 113.5 ft. Allowable headwater elevation is 110ft. Inlet invert is at natural stream elevation (no fall at inlet). Determine: If the culvert is adequate to convey the discharge Produce a performance curve that shows culvert discharge as a function of headwater elevation
What is the necessary height (P) of an overflow spillway that has a design discharge of 50,000 ft^3/s, if the upstream water depth is at an elevation of 800 ft, and the channel floor is at an elevation of 680 ft?The spillway is 180 ft wide. Use a discharge coefficient of 3.95 and √(ft)/s neglect the approach velocity. What is the necessary height (P) of the same spillway in Problem 1 if the approach velocity is now considered? Hint: use Hs from Problem 1 to solve for H.
Determine the normal and critical tie rods in a trapezoidal channel with a stencil width b = 3m, slope k = 1 and bottom slope S = 0.002. The Manning's roughness coefficient is n = 0.035 when conveys a flow Q = 15 m3/s. Also calculate the Froude number to determine the flow regime.
P2) If using a V-notch weir in 2.83m rectangular channel.The height of crest installed at 0.85m above the bed. For head=0.935m, and the tailwater= 1.44m, find the discharge.
A trapezoidal weir having side slope of 1H to 2V discharges 50 m3/s under aconstant head of 2m. Find the length of the weir assuming C = 0.60.
A trapezoidal channel flume is made of concrete (n = 0.014) slopes 0.3 ft per 1000 ft. a. Compute the discharge if the base is 6 ft with ? = 1/√3 and the depth of water is 3 ft.b. What would be the rate of discharge if the base were 3 ft and the depth of water 6 ft with m = 0.144?c. Which of the two forms would have the greatest capacity, and which would require less construction material?
A municipal WWTP receives 20,000m3/d of flow. They use two circular primary clarifiers operate in parallel which handle the flow equally. The state’s regulatory agency’s criteria are: Average overflow rate = 20 m3/(d·m2) and the average t0(θ) = 3.0 hours a. Determine the clarifier diameter. b. Estimate the side water depth. c. Calculate the weir loading rate in an inboard peripheral weir is used that is 0.25 m from the edge of the clarifier.
Find the water depth just upstream of a 4-ft-high broad-crested weir in a channel 10ft wide when the flow is 51.14 cfs
A grass-lined trapezoidal channel is to be designed to carry a flow of 260 cfs. Determine a suitable Manning’s first. The slope of thechannel is 1.5 ft/2000 ft. The side slopes (same both sides), z = (1 vertical : 2 horizontal). Use a b/y ratio of 1.25 and a maximumchannel width b = 12 ft.(a) Determine the design depth of flow for the channel [ft](b) Determine the other design parameters including the freeboard.(c) Is the flow in the channel under sub-critical or super-critical flow conditions? Why?(d) Sketch the profile cross-section of the channel with all necessary dimensions.
A grass-lined trapezoidal channel is to be designed to carry a flow of 260 cfs. Determine a suitable Manning's first. The slope of the channel is 1.5 fU/2000 ft. The side slopes (same both sides), z = (1 vertical : 2 horizontal). Use a bly ratio of 1.25 and a maximum channe width b = 12 ft. Determine the design depth of flow for the channel [fl (b) Determine the other design parameters including the freeboard. (C) Is the flow in the channel under sub-critical or super-critical flow conditions? Why? (D) Sketch the protle cross-section of the channel with a necessarv dimensions