Please explain the steps with the solution H.W.7 A rigid steel bar ABC is supported by three rods.There is no strain in the rods before load P is applied. Afterload P is applied, the axial strain in rod (1) is 1,200 µue.(1)2,000 mm(a) Determine the axial strain in rods (2).(b) Determine the axial strain in rods (2) if there is a 0.5 mmgap in the connections between rods (2) and the rigidbar before the load is applied.520 mm400 mm1,250 mm(2)

Answered: Image /qna-images/answer/53b4da7c-8914-442f-9163-1dacc9a23064.jpg

H.W.7A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is 1,200 uɛ. (a) Determine the axial strain in rods (2). (b) Determine the axial strain in rods (2) if there is a 0.5 mm gap in the connections between rods (2) and the rigid bar before the load is applied.

H.W.7A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is 1,200 uɛ. (a) Determine the axial strain in rods (2). (b) Determine the axial strain in rods (2) if there is a 0.5 mm gap in the connections between rods (2) and the rigid bar before the load is applied.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as -3800 μm/m. Use the dimensions L₁ = 1900 mm, L₂ = 1425.00 mm, a = 190 mm, b = 380 mm, and c=143 mm. Determine: (a) the normal strain in bar (1). (b) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin C before the load is applied. (c) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin B before the load is applied. L₁ Answer: (a) &₁ = (b) E₁ = A i i (c) E₁ = i 1 1 1 a B (1) b Rigid bar L2 με με με C (2)
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rod (2) is 1020 μin./in. Assume initial rod lengths of L1 = 148 in. and L2 = 78 in. Determine(a) the normal strain in rods (1).(b) the normal strain in rods (1) if there is a 0.043 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied.(c) the normal strain in rods (1) if there is a 0.043 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied.
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 2350 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normal strain in rod (2). (1) A L₁ (2) Rigid bar 1721 μm/m 1858 μm/m O 1347 μm/m O 1469 μm/m 943 μm/m B L₂ (1)
2. A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and length of the steel rod are given as 10 mm and 120 mm, respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0.53x 10 3, Given that the total extension of the composite rod must not exceed 0,162 4 mm and E for steel is 200 GPa, respectively. Calculate: a. Strain in the steel rod b. Load carried by the steel and brass rods d. Modulus of elasticity for the brass.
Q3) The rigid bar ABCD is supported by bars (1) and (2). After load P is applied, the normal strain in bar (1) is 820 µm/m. Find (a) the normal strain in bar (2). (b) The normal strain in bar (2) if there is a 1-mm gap in the connection at pin C before the load is applied. (2) 300 mm 340 mm 140 mm 1200 mm B D 900 mm (1)
2. A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and length of the steel rod are given as 10 mm and 120 mm, respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,53x 10-3. Given that the total extension of the composite rod must not exceed 0,162 4 mm and E for steel is 200 GPa, respectively. Calculate: a. Strain in the steel rod
2. A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and length of the steel rod are given as 10 mm and 120 mm, respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,53x 10-3. Given that the total extension of the composite rod must not exceed 0,162 4 mm and E for steel is 200 GPa, respectively. Calculate: d. Modulus of elasticity for the brass.
2. A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and length of the steel rod are given as 10 mm and 120 mm, respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,53x 10-3. Given that the total extension of the composite rod must not exceed 0,162 4 mm and E for steel is 200 GPa, respectively. Calculate: b. Load carried by the steel and brass rods
A short column tube of length L = 400 mm is loaded by a compressive force P. The outside and inside diameters are 70 mm and 60 mm, respectively. A strain gage is placed on the outside surface of the bar to measure normal strains in the longitudinal direction. E= 200 GPa. (a) If the measured strain is 550 x 10 -6 what is the shortening of the bar? (b) Determine the load P that will cause this strain. (c) Determine the compressive stress of the bar to produce this strain.