The 250 x 250 x 1.100-mm oak [E = 12 GPa] block (2) shown is reinforced by bolting two 7 x 250 x 1,100 mm steel [E = 200 GPa] plates (1) to opposite sides of the block. A concentrated load of 440 kN is applied to a rigid cap. Assume P = 440 kN, L = 1.10 m. Determine (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the block when the load is applied. e (2) CL 5 D e Calculate the cross-sectional area of each steel plate, A₁, and the cross-sectional area of the oak block, A₂.

The 250 x 250 x 1.100-mm oak [E = 12 GPa] block (2) shown is reinforced by bolting two 7 x 250 x 1,100 mm steel [E = 200 GPa] plates (1) to opposite sides of the block. A concentrated load of 440 kN is applied to a rigid cap. Assume P = 440 kN, L = 1.10 m. Determine (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the block when the load is applied. e (2) CL 5 D e Calculate the cross-sectional area of each steel plate, A₁, and the cross-sectional area of the oak block, A₂.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.
A 1000 kg homogenous bar 2 m long is suspended horizontally from two vertical cables A and B each 1.8 m long and connected at both ends. With cross-sectional area 400 mm sq. Determine the magnitude of the largest additional force acting downward which can be applied to the bar. The stresses in the cables A and B are limited to 100 MPa and 50 MPa respectively.
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
Two forces P1 and P2, with a magnitude of P1 = 15 kN and P2 = 18 kN, are applied as shown in Figure below to the end A of bar AB, which is welded to a cylindrical member BD of radius c = 20 mm. Knowing that the distance from A to the axis of member BD is a = 50 mm and assuming that all stresses remain below the proportional limit of the material, determine the normal and shearing stresses at points H and K of the transverse section of member BD located at a distance b = 60 mm from end B,
A thin-walled cylindrical vessel has an internal diameter of 1 m and a thickness of 10 mm subjected to an internal pressure of 2 bar. The vessel surrounded by two semicircular rings tightens by two bolts as shown in the figure below. knowing that the diameter of the bolt is 12 mm and the length of the vessel is 4 m, determine the tensile stress induced in the bolt.
A solid aluminum [E = 64 GPa] rod (1) is connected to a solid bronze [E = 114 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 36 mm and bronze rod (2) has an outside diameter of 17 mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the bronze rod must be limited to 92 MPa. Assume L1 = 168 mm and L2 = 399 mm. Determine: (a) the maximum downward load P that may be applied at flange B. (Answer: P = 146kN)(b) the deflection vB (downward is positive) of flange B at the load determined in part(a). (Answer: vB = .322 mm)
Rigid bar ABCD is loaded and supported. Bars (1) and (2) are unstressed before the load P is applied. Bar (1) is made of bronze [E= 100 GPa] and has a cross-sectional area of 400 mm2. Bar (2) is made of aluminum [E= 70 GPa] and has a cross-sectional area of 600 mm2. After the load P is applied, the force in bar (1) is found to be 60 kN (in compression). Determine: (a) the stresses in bars (1) and (2).(b) the vertical deflection of point A.(c) the load P.
A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of 200 MPa. The rod is 250 mm long and one part of its length is square and the remainder is circular with a diameter of 25 mm. If the total strain energy in the rod and modulus elasticity of the material is 1.3 J and 200 GPa, determine the following:1.The applied load F2.The total extension of the bar3.The length of the square portion of the bar4.The suddenly applied load that will induce the same amount of energy 5.The load that falls from a height of 8 mm induces 1,3 J in the bar.
Straight rods of 0.30-in. diameter and 200-ft length are sometimes used to clear underground conduits of obstructions or to thread wires through a new conduit. The rods are made of high-strength steel and, for storage and transportation, are wrapped on spools of 5-ft diameter. Assuming that the yield strength is not exceeded, determine (a) the maximum stress in a rod, when the rod, which was initially straight, is wrapped on the spool, (b) the corresponding bending moment in the rod. Use E= 29 * 106 psi.
A steel [E= 30,000 ksi] pipe column with a cross-sectional area of A1=5.60 in 2 is connected at flange B to an aluminum alloy [E= 10,000 ksi] pipe with a cross-sectional area of A2=4.40 in 2. The assembly is connected to rigid supports at A and C. For the loading shown, determine: (a) the normal stresses in steel pipe (1) and aluminum pipe (2).(b) the deflection of flange B.
A-36 Aluminium rod shown in figure Q1a is 2.5 m long and must not stretch more than 1.5 mm when an 10.5 kN load is applied to it. Knowing that E = 75 GPa, determine (i) the smallest diameter rod which should be used, (ii) the corresponding normal stress caused by the load.