H.W.7: For the transverse exterior frame (Frame D) of the flat plate floor, without edge beams, shown in Figure, and by using the Direct Design Method, find: a- Longitudinal distribution of the total static moment at factored loads. b- Lateral distribution of moment at interior panel (column and middle strip moments at negative and positive moments). Given: Slab thickness = 180 mm, d = 150 mm, w = 15.0kN/m², All columns = 400 x 400 mm. -5.0 m- 5.0 5.0 Frome D 6.0 m

H.W.7: For the transverse exterior frame (Frame D) of the flat plate floor, without edge beams, shown in Figure, and by using the Direct Design Method, find: a- Longitudinal distribution of the total static moment at factored loads. b- Lateral distribution of moment at interior panel (column and middle strip moments at negative and positive moments). Given: Slab thickness = 180 mm, d = 150 mm, w = 15.0kN/m², All columns = 400 x 400 mm. -5.0 m- 5.0 5.0 Frome D 6.0 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam
An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at C, and a roller at point A and also in point B (where it settled 25 mm downwards here). The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4 .Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.
The moment diagram (answer in kips) P=8.3 kips, b = 23 ft, h=13 ft
An elevated water tank weighs 3000kN when filled with water, the centroid of the mass being at a height of 9 meters from ground. The horizontal spring factor for the tank tower is 15 kN/mm. Determine the shear force generated at the base of the water tank tower by horizontal seismic inertia force. Assume the ground motion has a period of 2.0 sec and maximum acceleration of 0.15g
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
Consider the object shown. Suppose that P = 390 N . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.8 ft, b = 3.5 ft, P = 30 kips, and w = 2.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45degrees, determine the smallest force P required to raise block A.
Assuming clockwise moments as positive, compute the moment of force F = 90kN at points A and D. If each square is 1m on a side.
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 1.6 m, E = 11.62 GPa , and I =1694446mm4.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.4 ft, b = 3.5 ft, P = 30 kips, and w = 1.2 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum moment. calculate? A:0 B:7