Half-Wave Controller A single-phase ac voltage controller in Figure 11.2a has a resistive load of R = 10 and the input voltage is V_{1} = 120V 60 Hz. The delay angle of thyristor T is alpha = pi / 3 Determine (a) the rms value of output voltage V, (b) the input PF, and (c) the average input current.

Half-Wave Controller A single-phase ac voltage controller in Figure 11.2a has a resistive load of R = 10 and the input voltage is V_{1} = 120V 60 Hz. The delay angle of thyristor T is alpha = pi / 3 Determine (a) the rms value of output voltage V, (b) the input PF, and (c) the average input current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

During turn-on and turn-off of a power transistor, thecurrent-time and voltage-time relationships are asshown in the adjacent figure. Observe the waveformsand calculate,40) the OFF-state power dissipation (static);41) the switch ON-state power dissipation(static);42) the average switching loss for the OFFtransition (dynamic);43) the average switching loss for the ONtransition (dynamic);Assume a switching frequency of 2kHz with 397V as specified in Appendix A.
1) Explain the Voltmeter PMMC instrument and the Ammeter PMMC instrument in AC?2) What are the benefits of using an Auto Transformer instrument in AC?
Describe different control schemes of AC regulators and derive the expressions of average andeffective values of output voltages. i need a short answer and correct answer plerase
2. A load of 8Ω is supplied by a single-switch Direct Current (DC) chopper with an inputvoltage of 40V. The switching frequency is 800Hz, the duty ratio is 0.4, and thetransmission voltage drop of the transistor is 2.4V a. Draw the chopper circuit presented in the question b. Find the switching period with the duty time of BJT c. Draw the load voltage, load current, BJT current, BJT voltage along two periods d. Find the output voltage. Is the achieved load voltage the average value or the effectivevalue e. Find the output power f. Find the average value and effective value of BJT current g. Find the power loss of BJT h. Find the DC source current i. Find the circuit efficiency
This mode of control is not recommended for disturbances that are erratic and noisy in nature. a. integral b. on/off c. proportional d. derivative What is calculated as the error in a negative feedback loop? difference between measured variable and load difference between load and set point difference between load and process output 4. difference beween measured variable and set point A proportional controller whose gain has a very large value approaches which mode of control? on/off proportional-derivative proportional-integral proportional-integral-derivative
For a single-phase Ac-Ac Converter with unidirictional phase control, find the output dc voltage, where, the delay angle is 0 degree, the input voltage is 120sinwt with 10ohm resistive load consider
A) What does VCO stand four? Show by drawing the relationship between its input and output signals. Compare VCO circuit with LC Tank circuit in terms of circuit functionality and how the output is generated in each of them. B) Compare between AM and FM in terms of noise immunity, interference, equipment complexity and cost and line of site transmission.
A unit feedback system has (see picture below) If subjected to unit step input, determine: a) Damped frequency of oscillations, b) time for first overshoot, c) settling time, d) maximum peak overshoot, e) stability
Sketch the circuit diagram of a balancing circuit for a differential amplifier.
TOPIC: AMPLITUDE MODULATION AND DEMODULATIONPlease answer this 2 question thanks.1. What is the different degree of modulation?2. What are the limitations of square law modulator?
If a sinusoidal voltage is applied to the base of a biased npn transistor and the resulting sinusoidal collector voltage is cut to near zero volts, what is the state of the transistor? Please select one: a. answers B and C b. interrupted drive c. answers A and C d. forced into nonlinear operation e. drifting into saturation
Vary the gain and time constant model parameters. How do the gain and the time constant affect the system response?