handle should be identified as a point of interest. Determine the Degree of freedom.

Q: -In the clevis shown in Fig. below, find the minimum bolt diameter and the minimum thickness of each...

A:

Q: Liquid oxygen is stored in a thin-walled, spherical container 0.8 m in diameter, which is enclosed w...

A:

Q: A spring with an unstretched legth of 5 inches expans from a length of 2 inches into a legnth of 4 i...

A:

Q: Write shear & moment equations as function of x and draw shear & moment diagrams for the beam given ...

A:

Q: This equilibrium phase of steel only occurs at temperatures above 723° C: martensite ferrite austeni...

A: Austenite

Q: 1. If the pulleys. veightless and frictionless, find the acceleration of body

A: Given:

Q: If the allowable stress of a revolving steel is 150 MPa, what is the equivalent angular velocity whi...

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any sp...

Q: 2 kg of steam is at 10 bar and 0.8 dry. Determine its enthalpy, entropy and volume (use steam table)...

A: Given that, m=2 kg, p=8 barx=0.8 Enthalpy of steam for 1 kg mass,     h=hf+x·hfg=720.9+0.8×2046.5=23...

Q: (a) Explain the steps involved in representing the natural a flows within a building using the nodal...

A: Natural and mechanically driven air flows The paper portrays a displaying investigation of hotness m...

Q: system interacts to equilibrium with a reference

A: Given; Maximum theretical work obtainable,when a system interacts to equilibrium with a reference en...

Q: 2m D B 2 m 3 kN 8 kN 2 m 2 m

A:

Q: F1 of 3 ft F2 E 3 ft A If F1=235 Ib and F2=380 lb Determine the force in each member and identify wh...

A:

Q: ᴀ ᴘᴜᴍᴘ ᴅᴇʟɪᴠᴇʀꜱ 500 ɢᴘᴍ ᴏꜰ ᴡᴀᴛᴇʀ ᴀɢᴀɪɴꜱᴛ ᴀ ᴛᴏᴛᴀʟ ʜᴇᴀᴅ ᴏꜰ 200 ꜰᴛ ᴀɴᴅ ᴏᴘᴇʀᴀᴛɪɴɢ ᴀᴛ 1770 ʀᴘᴍ. ᴄʜᴀɴɢᴇꜱ ʜ...

A: As per given question  H1=200ft H2=375 ft N1=1770 rpm We have to determine N2

Q: PROBLEM 20:In a conventional refrigeration cycle which uses Freon-12 as the refrigerant, the tempera...

A: according to the given details:  

Q: Does line AB intersect with parallel lines YZ and WX? Complete all views

A:                                                                      

Q: using generalized Vogel's equation. The fol- ata are given: r pressure, p = 5,500 psia oint pressure...

A: Well A : pwf1>pb          J* =q1p¯ -pwf1             =4005500-4000=0.2667 stb/day/psi    qb=J*p¯ ...

Q: 1.) A player that is 1.5 m tall shoots a basketball to the hoop which is 10m away from him. The hoop...

A:

Q: 3) Compute the centroid of the shaded area shown in figure Q.3 y R50 R30 120 100 25 50

A:

Q: A submarine is rolling under seawater whose radius of gyration is 12 m and period of oscillation of ...

A:

Q: Which of the following is FALSE about the shear diagram? Select one: a. It provides an easy way to d...

A: This question is based on the concept of strength of material

Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm...

A:

Q: Calculate the diameter size of the cylinder required to exert force 1000N on the piston rod with pre...

A:

Q: A Diesel cycle operates with a compression ratio of 13.5 and with a cutoff occurring at 6% of the st...

A:

Q: For the beam with FBD shown in Figure 2, what is the expression for the bending moment M in terms of...

A: Given

Q: The car A has a forward speed of 33.0 km/h and is accelerating at 2.3 m/s2 . Determine (a) a speed a...

A:

Q: For the system illustrated in the figure, determine the value of "h" that puts the system un equilib...

A: Find the value of h to system in un equilibrium.

Q: Q3) There is a heat flux through a wall of 2250W/m. The same is dissipated to the surroundings by co...

A:

Q: y W (N/m) В 5 m 10 m 12 m A beam of length 12 m is in equilibrium, the force is distributed 540 in m...

A: Given Data L=12 m w=540 N/m

Q: Due to slipping, points A and B on the rim of the disk have the velocities va = 7.2 ft/s and vg = 14...

A:

Q: Read the problem carefully and provide complete solutions with derivation of formulas(inte...

A:

Q: )A race car starts accelerating at a = 5 and continues to do this for 10 seconds. What is its final ...

A:

Q: Pulleys - Cords Stopper Container Water Stopcock Ball Float

A:

Q: Please calculate the sound pressure level, in dB, of a noise with a sound pressure of 0.9

A:

Q: From the influence line of moment at D, what is the value of moment Mp when x = 13 m due to a unit l...

A:

Q: Suppose the rated speed of a highway curve of 300 ft. radius is 40mph. If the coefficient of frictio...

A:

Q: 1. The armature and shunt field resistance of a 50-kW, 220 V shunt generator is 0.026 ohm and 52 ohm...

A:

Q: 60° ) = 8 rad/s 500 mm a = 16 rad/s? 150 mm B 30°

A:

Q: Which of the following equations corresponds to the magnitude of the internal shear of section a-a'?

A: For the simply supported beam, it is required to determine the internal shear at section a-a'. RA = ...

Q: A heavy cask (full of wine!) sits on an inclined plane. It is held in place by a rope that is attach...

A:

Q: B C E -5 m- -8 m- -8 m- -5 m-

A:

Q: Determine the moment about point B for each of the individual three forces acting on the beam, and i...

A:

Q: Enumerate and briefly explain the sources of aircraft noise.

A:

Q: A punch punches a 1-in. diameter hole in a steel plate % inch thick every 10 sec. The actual punchin...

A:

Q: ɴᴀᴍᴇ ᴛʜᴇ ᴘᴀʀᴛꜱ ᴏꜰ ʜᴏʀɪᴢᴏɴᴛᴀʟ ᴄᴇɴᴛʀɪꜰᴜɢᴀʟ ᴘᴜᴍᴘ. and ᴡʜᴀᴛ ᴀʀᴇ ᴛʜᴇ ᴄᴜʀᴠᴇ ᴛʜᴀᴛ ᴀʀᴇ ɴᴏʀᴍᴀʟʟʏ ᴠɪꜱɪʙʟᴇ ᴏɴ ᴀ...

A: Horizontal centrifugal pump :

Q: Find the brake power of the engine running at 755 rpm. The length of lever from centre of pulley is ...

A:

Q: 5. Types of Grinding Wheel Machines and their outputs. (atleast 3)

A: Types of grinding machine: Floor or bench grinder: This is a small type of machine used in the works...

Q: A river section shown has an initial volume of 600m with 750g of phosphorus. The discharge from the ...

A: (a) Write the discharge from upstream. Q1=100 m3day2gm3=200 g/day

Q: Q1. Collar A moves at a velocity, V4, to the right. The values of the kinematic parameters are given...

A:

Q: State the uses of each tools: 1. parting off tool 2.boring tool 3. undercutting tool

A: Parting off tool is a lathe tool which is a blade like cutting tool. It is used to remove the finish...

Q: A sudden enlargement in a circular duct measures 0.20 m diameter upstream and 0.40 m downstream. The...

A: Answer: The flow rate through the duct is 0.38 m3/sec.  

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.