he sway frame shown below is supported by fixed supports at A and D. The frame carries the loading indicated in the figure below. All the members have constant stiffness E and the moment of inertia of each member is indicated in the figure. a- Using the slope-deflection method, calculate the reactions at the supports b- Draw the shear force and bending moment diagrams. Sketch the deflected shape 20 kN/m 15 kN C 1.51 4m D 5m 2m

he sway frame shown below is supported by fixed supports at A and D. The frame carries the loading indicated in the figure below. All the members have constant stiffness E and the moment of inertia of each member is indicated in the figure. a- Using the slope-deflection method, calculate the reactions at the supports b- Draw the shear force and bending moment diagrams. Sketch the deflected shape 20 kN/m 15 kN C 1.51 4m D 5m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the given frame shown, determine the following using cantilever method. 1. What is the location of the centroid from the rightmost column? In m.2. What is the axial force at column CF? in kN.3. What is the moment AD at joint D? in kN.m.
For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?
An Analyze the frame shown in the figure. Use Cantilever Method. 68. Compute the centroid of columns from the rightmost. a. 7.33 m b. 6.33 m c. 8.33 m d. 5.33 m 2. Compute the axial force on column CF. a. 2.687 kN b. 2.786 kN c. 6.287 kN d. 7.268 kN 3. Compute the moment in column A.D a. 7.605 kN.m b. 5.706 kN.m c. 6.705 kN.m d. 6.507 kN.m
Use Area-Moment Method in solving the problem. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
The frame is loaded as shown in the figure. The supports at A is fixed and D is hinged. Use Slope-Deflection in determining the following: a.Unknown rotations or displacement b.Moments at each segment c.Reaction at the given supports. E = 210 GPa
In the figure, there is a joint at the C point in the AB beam, one end of which is fixed and the other end is held with a sliding support. Of beam its cross section is given below. To the beam, as shown in the figure between CB and 100 kN from point B An axial load of magnitude acts. a) Draw the bending moment diagram (influence line) and find the absolute maximum bending moment value. b) Where the absolute maximum moment found in (a) occurs, at point P shown in the cross section Determine the state of the stresses. c) Find the principal stresses and axes for the stress condition you calculated at point P.
For the beam and loading shown below, determine the reactions at supports A and B. Assume that EI = 8.6× 106 kip·in.2 is constant for the beam. Use w = 11 kips/ft and L = 12 ft. Remove support C and use the appropriate equations from Appendix C to calculate the deflection at point C caused by the distributed load. Use the sign convention from the textbook (deflection is positive upward).
The structure of a beam with single supports is subjected to a moment MA at the pinned end A, an inclined load FB applied at point B, and a uniformly distributed load with intensity q1 on the segment BC. Find the support reactions at joints A and C, then calculate the internal forces at the midpoint of BC. MA= 380 N.m FB = 200 N q1= 160N/m a= 3 m b= 2m
There is a joint at the C point in the AB beam, one end of which is fixed and the other end is held with a sliding support. Of beamits cross section is given below. To the beam, as shown in the figure between CB and 100 kN from point BAn axial load of magnitude (35 P) is acting.a) Draw the bending moment diagram (influence line) and find the absolute maximum bending moment value.b) Where the absolute maximum moment found in (a) occurs, at the point P shown in the cross sectionDetermine the state of the stresses.c) Find the principal stresses and axes for the stress condition you calculated at point P.
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
The 600mm diameter steel shaft is subjected to the torques shown. Determine the angle of twist of end A with respect to C, in . Assume G = 75 GPa. P=74 Ex. 3P= 3(74) = 222 2P= 2(74) =148