help me plot the horizontal and vertical distance using free hand

Q: Determine the coordinates of the 60 mm Centroid of the shaded area shown 30 mm in item 3. 30 mm X 45…

A:

Q: Sketch thefollowing figure ,orthographic view ( using catia )  Metion the top view side view and…

A: From figure.......

Q: Draw the orthographic Projections of given object.

A:

Q: Choose the best option, how to select set of objects in a drawing? Ctrl + clicking on the objects.…

A: Ctrl + A is used to select set of object in drawing

Q: Construct a diagonal scale of RF =1/2500 to show meter and long enough to measure upto 500 meter.…

A: Diagonal Scale: The diagonal scale is used to represent three units. The three units are the main…

Q: Draw in full scale front view ( indicated by the arrow F), top view and left-side view of the…

A: to find top , front and left view

Q: Locate the X-X centroidal axis for the cross section shown. £ sym. W840 x 329 W530 × 72 X X

A:

Q: 2.

A: FRONT VIEW observe the diagram in the direction of the arrow and draw the shorter side of the box…

Q: Determine the y-coordinate of the centroid of the shaded area shown. 9" Parabolic. 4" Answer: y = i…

A:

Q: Draw isometric view of triangular pyramid of base edge 40mm and height 50mm by hand

A:

Q: 6. Draw a true distance between a point Q and a plane B. Vs he 7. Draw a piercing point and…

A:

Q: Q3. For the object shown, sketch a third-angle orthographic projection of the object showing all the…

A:

Q: Draw the orthographic projections of given objec

A: Orthographic projection contain side front and top view

Q: Draw the isometric perspective and the ortogrophic views of the object (4 views in total). Indicate…

A: Solution:- The Isometric & Other 3 Views of the figure are mentioned below with the Dimension.

Q: Given the Isometric View, draw the following: Top View Front View Right Side View Section View…

A: (Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three…

Q: FIND THE LENGTH OF THE DIVIDING LINE DP. THANK YOU. (THIS SUBJECT IS SURVEYING)

A:

Q: 120 22 56 34 44 RS O-2 Holes Top view Isometric view 36 64 40 26

A: Answer:- A- A Section and top view:

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

A:

Q: Draw in full scale the front view (indicated by the arrow A), top view and right-side view of the…

A: a}

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: Q1: Draw the orthographic Projections of given object. 10 R25 R15 R5 R10 R5 R10 100

A: Given

Q: There are a couple errors in the multi-view drawings below (the isometric is accurate and assume any…

A:

Q: Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: Instructions :  To draw orthographic projections using third angle projection method, take the view…

Q: Draw projections of a 80 mm long line PQ. Its end P is 10 mm above HP and 10 mm in front of VP. The…

A:

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L 1. Discuss how did you draw…

A:

Q: tle: Orthographic Projection Draw the orthographic views of the object below with dimensions. (Top,…

A:

Q: 10. 45 8.3 SUPPORT BRACKET 100 33 10 10 25 -

A: Question being asked here is to draw the ISOMETRIC VIEW for the given projections And the given…

Q: Draw in full scale the front view (indicated by the arrow A), top view and right-side view of the…

A: (c) Top view is shown below;

Q: Draw the orthographic views of the object below with dimensions. (Top, Front, Right views) m,00…

A:

Q: Required: Draw the front projection, the left side projection, the horizontal projection

A:

Q: Instruction: Dew the 3D Dewing hometric View) of the indicated 2D Orthographic Projection You can…

A: From the given question it is required to draw the 3D drawing of the 2D orthographic projection. for…

Q: Write a short note on:  Aligned dimensioning. Unidirectional dimensioning.

A: In this system of dimensioning, the dimensions are written along the same direction in the entire…

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: noose best option. how would you ct set of objects in a drawing? * None of the above By a crossing…

A: By a crossing window is drawn from right to left the set of objects can be selected. Option (b) will…

Q: Draw Multiviews

A: The front view, side view, and top view of figure 1 are below:

Q: Engineering Mechanics Draw the figure. Put the directions if clockwise or counterclockwise and if…

A:

Q: Need clear and complete solutions. Determine the coordinates of the centroid of the shaded area. 10…

A: Given data

Q: Draw the isometric view for the given figure.

A: Isometric view:- In engineering and technical drawings, isometric projection is a method for…

Q: Draw the orthographic view given the isometric drawing.

A: Explanation :  To draw orthographic projections using third angle projection method, take the…

Q: Draw a diagonal scale 20mm: 1m up to 8m and indicate 6.74m

A:

Q: Find the shortest distance from point B to line AC

A: x0OB=7j-3kx1OC=7j+5kx2OA=12i Shortest distance

Q: 21 19 8.5 المطلوب : 75 المقطع الأفقي خلال أ.i 20 35 196 75 Draw on paper Front view Side view And…

A:

Q: Given the figure that shows front and top views of the object, how many of its visible and hidden…

A:

Q: Given the top view and right side view, draw the sectional view of the figure (you may use…

A: The sectional view is drawn in the next step for the given views

Q: A Figure 2 shows an isometric view of an object. Draw to a full size scale the following views in…

A: Data Given: Asked: Sectional Front View Top View Sectional Side View

Q: 10cm- 16 cm

A: Given:- To find:- From a given figure it is required to find out the centroidal coordinates of the…

Q: Write the command to draw Figure below by using Auto CAD program (Relative Polar Coordinate Method -…

A: First we will draw the base line or construction line:- Note: for enter command, we can press space…

Q: Define the following terms. (a)       Line of collimation, Axis of telescope, Back sight, Fore…

A: The definitions are as follows a) Line of collimnation or Line of sight is the line that joins the…

Q: A line AB is 40 mm long.Endpoints A & B are 20 mm in-front of Vertical Plane.Endpoints A is 15 mm…

A: Trace is the point of intersection of a line with any plane then that point of intersection is…