Help your customer to calculate the heat losses through a composite wall that includes an 8-mm-thick hardwood siding, 40-mm by 130-mm hardwood studs with glass fiber insulation (paper faced, 28 kg/m3 ), and a 12-mm layer of gypsum (vermiculite) wall board as shown. The wall is 2.5 m high by 6.5 m wide. - 20 °C Wood siding Stud 130 mm Insulation Wall board 21 °C 40 mm Figure 1: The top view of thecomposite wall.

Help your customer to calculate the heat losses through a composite wall that includes an 8-mm-thick hardwood siding, 40-mm by 130-mm hardwood studs with glass fiber insulation (paper faced, 28 kg/m3 ), and a 12-mm layer of gypsum (vermiculite) wall board as shown. The wall is 2.5 m high by 6.5 m wide. - 20 °C Wood siding Stud 130 mm Insulation Wall board 21 °C 40 mm Figure 1: The top view of thecomposite wall.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter2: Concepts In Structural Steel Design

Section: Chapter Questions

Problem 2.5P

See similar textbooks

Similar questions

A furnace wall is composed of three layers, 25cm firebrick (k=1.65W/m·K), followed by 20 cm of kaolin insulating brick(k=0.078W/m·K), and finally 15 cm of masonry brick(k=1.25W/m·K). The temperature of the inner wall surface is 935°C and outside surface is at 35 °C. Assume that surface area is 1m². (1)What is the energy transfer rate q(W)? (2) What are the temperatures at the two contacting surfaces?
Assuming you apply 5/8” coating of gypsum wallboard to the non-fire exposed side of a 6” thick siliceous concrete wall, what is the new effective thickness to be used to determine the resistance of the wall?
Steel forms will be used to cast a 12 in. thick wall in cold weather with concrete containing 300 lb/ydl ofType I cement. The wall will be wrapped with a 2 in. thick blanket made with mineral fiber insulation. Assuming linear interpolation is appropriate, what is the minimum acceptable surrounding ambient temperature for 3 days curing without providing additional protection?
Assume a concrete cover of 40 mm, 10mm stirrups and clear distance between layers of 25mm.
A wide-flange WF 24 x 76 steel beam with 1 in. (25.4 mm) of spray-applied cementitious material (British equivalent 610 x 229 x 113 kg/m). The beam has WID 1.03 lb/ft and nowhere does the temperature exceed 1,000 F (538 C) or 811 K. The insulation temperature is to he 750 F while keeping the steel temperature at 538 C. The results obtained from (a) Malhotra's quasi-steady state approach (b) Jeanes' graph (c) Lie's graph are compared. To calculate the fire resistance R for the spray-applied beam, the following data are used:
Determine the quantity of the following materials to be use for wall (H=1.50m, W=3.00m, L=5.00 m.), Floor dimensions = 3.00 x 5.00m. a. 40 x 40 cm. glazed wall tiles; b. 60 x 60 cm unglazed floor tiles
Given: Project Description A single-family detached house with floor plan shown in Figure 1 is located in Charlotte, NC (Latitude: 35° N). Ceiling height is 2.4 m. The garage is unconditioned while all other spaces are conditioned. The house has the following construction characteristics: Roof: Attic roof with asphalt shingles Ceiling: Flat wood-frame ceiling with blow-in fiberglass insulation, U-factor= 0.18 W/m2-°C Doors: Wood, solid core doors, U-factor = 0.51 W/m2-°C Floor: Slab-on-grade floor with heavy carpet over rubber pad (Thermal resistance of floor covering Rcvr=0.21 m2*°C/W); R-0.9 edge insulation to 1 m below grade; Fp= 0.85 W/m-°C; Windows: All windows are clear double-pane glass in vinyl frames The window in the living room is a fixed picture window. All other windows are vertical sliding windows operable with insect screens White roller interior shades, half closed Overhang: eave overhang along all four sides of the house; overhang depth = 0.6 m; eave edge at the same…
What is Damping Capacity.
With FBD Complete soltion please thank you
Which one of the following equations isdimensionally homogeneous? Show yourproof.
Difference between Heat Island Effect: Roof and Heat Island Effect: Non-roof.
Explain the structutre of Insulation Between the Roof Deck and the Membrane.