Q1/ The west wall in a building in Baghdad (32°N) has a window of the dimensions (1.0 m x 2.0 m). The glass is of heat absorbing type (U= 4.6 W/m?ºC) and thickness of 6 mm.. Outdoor design condition is 34°C DBT, with daily range of 11°C, and indoor design temperature is 24°C. Calculate the cooling load from the window at 4:00 P.M. in the month of August.

Q1/ The west wall in a building in Baghdad (32°N) has a window of the dimensions (1.0 m x 2.0 m). The glass is of heat absorbing type (U= 4.6 W/m?ºC) and thickness of 6 mm.. Outdoor design condition is 34°C DBT, with daily range of 11°C, and indoor design temperature is 24°C. Calculate the cooling load from the window at 4:00 P.M. in the month of August.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 27P

See similar textbooks

Similar questions

Find the heat load for the following side of a house for a 70°F design temperaturedifference. The wall is a wood frame with siding and 31⁄2 inches of insulation. The windowis double pane.
9. A computer room located on the second floor of a five-storey office building is 10m X 7m. The exterior wall is 3.5m high and 10m long; it is a metal curtain wall (steel-backed with 10mm of insulating board), 75mm of glass fiber insulation, and 16mm of gypsum board The single-glazed window (U=5.9 W/m2-K) make-up 30% of the exterior wall. Three computer sets at 500 Watts each and 500 Watts of total lighting power in the room operate 24 hours per day. The indoor temperature is 20°C. Determine the following: a. The heat load, in Kilowatts, if the outdoor conditions is 32°C DB and 23°C WB. b. What would be the load, in Kilowatts, if the windows were double-glazed (U=3.5 W/m2•K)?
While the pressure remains constant at 85 psig, the volume of air changes from 20 ft3 to 12 ft3. Find the amount of work done on or by the closed system?
b.) calculate the outside air flow for the restaurant dining area where cold air is supplied from the ceiling, lit/sec
A two-story building of volume of 540 m3 has an effective air leakage area of 510 cm2. The outdoor and indoor design temperatures for winter conditions are í10°C and 20°C respectively. The average design wind speed is 7msí1. The house is sheltered by other houses across the street. Estimate (i) the air infiltration rate, and (ii) the air exchange rate per hour.
Calculate the total cooling load for a building at 32° North latitude at time 14 on 21 of August, outdoor design temperature 35 °C, daily range DR = 11.1 deg ⁰C and indoor design temperature 25.5°C. The building has the following data: A-The ceiling is constructed from 152.4 mm lightweight concrete (I.W concrete) and without a suspended ceiling, dark colour (k = 1) and no mechanical ventilation (f = 1) . Area= 25 m². B-South window consists of 3 mm one layer without internal shading, area=4 m², U = 4.5 W/m2 °C. Assume shading coefficient SC = 1 and cooling load temperature difference CLTD=7 °C and cooling load factor CLF=0.55. C- West wall is constructed from 101.6 mm heavyweight concrete wall+finish (H.W. concrete wall+Finish) (group E) and medium colour (k = 0.83) Area= 17.5 m². D-There is another window that has one hinge that causes an infiltration rate of 5 L/(s.m) of infiltrated air. The moving window has a height of 1.5 m and a width of 1 m. E- Four occupants in the…
What is the size (ft) of the grille needed to pass 180 cfm at 60 ft/min velocity? Assume free air at 80%.
Air at 30 deg. Celsius and 110KPa flows at 20N/s through a rectangular duct that measures 160mm x 320mm. Compute the average velocity (m/s) and flow rate (? ^3/s) using gas constant equal to 289 J/kg-K.
Answer ONLY items 5-8. Room dimensions are: LxWxH = 8.50 m, 5.0 m, 3m. Originally, the room had linoleum flooring with an absorption coefficient of 0.03. Two opposite walls were cladded with unglazed bricks with an absorption coefficient of 0.02, the one having the entrance gypsum door (2.1 m X 0.80 m) with 0.05 abs.co.; the other two were just bare concrete with sliding glass window openings of 1.80m x 1.20 m each; the bare concrete with an abs.co. Of 0.31 and the window glass with 0.18, the ceiling, too , had bare concrete as its finish at 500 Hz. The client would like to renovate the space into an acoustical studio room and would like to change the ceiling and the flooring. The ceiling will have a vinyl faced fiberglass panel with an abs.co. of 0.71, and the floor will have mineral fiber tiles with an abs.co. Of 0.66, all at 500 Hz.
A warehouse measures 40 feet by 50 feet and has 20-foot-high walls. Thewarehouse was built on a concrete slab and has 6 inches of insulation inthe wood frame walls and 91⁄2 inches in the ceiling. There are no windowsin the building, and the door is made just like the walls. What is the heat loadfor this warehouse in an area where there is a 75°F design temperaturedifference?
If the room in problem 16 faced the sun, an additional cooling load would becreated. This extra cooling load would be due to the sun shining through thewindow and heating the room. A window facing south would allow a maximumof 75 Btu per hour to enter the room for each square foot of window area. Ifthe room has its window facing south, what is the maximum cooling load forthe room?
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 20 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = kJ. Answer b. If the reverse side surface temperature is maintained, determine the hourly heat loss incurred = kJ.Answer