H 2. 3.4-4 A992 steel is used for the tension member shown in Figure P3.4-4. The bolts are 3/4 inch in diameter. The connection is to a %-in.-thick gusset plate. a. Determine the nominal strength based on the gross area. b. Determine the nominal strength based on the effective net area. W16 x 40 2″||+34"-3"-|| T 3½" | * * * * * * * *

H 2. 3.4-4 A992 steel is used for the tension member shown in Figure P3.4-4. The bolts are 3/4 inch in diameter. The connection is to a %-in.-thick gusset plate. a. Determine the nominal strength based on the gross area. b. Determine the nominal strength based on the effective net area. W16 x 40 2″||+34"-3"-|| T 3½" | * * * * * * * *

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.6P

See similar textbooks

Similar questions

The 1 × 8 plate is shown in the figure. The holes are for 3/4-in Ø bolts. Compute the net area of each of the given members. (Ans. 6.44 in^2)
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.
Bottom chord of truss is composed of two angle bars each having a dimension of 151 mm x 198 mm x 7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 38 mm and 55.8mm pitch. Use A36 steel Fy = 248 MPa Fu = 400 MPa spacing of bolt = 67.3 mm Compute the capacity of the bottom chord based on block shear strength, in KN.
A double-angle shape, 2L6 × 6 × 5⁄8, is connected to a 5⁄8-inch gusset plate as shown inFigure P7.6-1. Determine the maximum total service load that can be applied if the ratioof dead load to live load is 8.5. The bolts are 7⁄8-inch-diameter, Group A bearing-typebolts. A572 Grade 50 steel is used for the angle, and A36 steel is used for the gusset plate.a. Use LRFD.b. Use ASD.
Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity of the connection in double shear? Assume that the shear planes pass though the threaded portion. State the condition necessary for these strengths to be available. (Draw the connect first and calculate the capacity)
Two flat bars loaded in tension by force P are spliced using two rectangular splice plates and two 0.350 in. diameter bolts. Away from the connection, the bars have a width of b = 0.625 in. and a thickness of t = 0.15 in. The bars are made of polyethylene having an ultimate tensile strength of 3200 psi and an ultimate bearing strength of 1500 psi. The bolts are made of nylon that has an ultimate shear strength of 4400 psi. Determine the allowable load P for this connection if a safety factor of 3.7 is required. Consider tension and bearing in the bars and shear in the bolts. Disregard friction between the plates.
9) what is the weld capacity of the shear connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
Design a weld connection for an UNP 280×80×9 of S 355 (fy= 355 MPa and fu= 470MPa) steel connected to a 10 mm gusset plate. The guesst plate is S275. Please draw all calculated values on a sketch with full dimensions. D= 335 KNL= 670 KN
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.