Homework// Estimate_k and a in the infiltration equation (D = ktª) (‡ in minutes and D in mm) for a water run by using the following information: Inflow (q) is 5.5 l/sec per 1 m of the width Depth of flow at the beginning of the water run is 5 cm The infiltrated depths are distributed as a parabola The recorded data of water advance are as follows: Time (t) in minutes ● 30 80

Homework// Estimate_k and a in the infiltration equation (D = ktª) (‡ in minutes and D in mm) for a water run by using the following information: Inflow (q) is 5.5 l/sec per 1 m of the width Depth of flow at the beginning of the water run is 5 cm The infiltrated depths are distributed as a parabola The recorded data of water advance are as follows: Time (t) in minutes ● 30 80

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13. Situation 5 - A 0.60 m diameter pipeline 30 m long carries 0.4 m^3/s of water. a. Compute the head loss, in meters, if n = 0.014. Round off to three decimal places. b. Compute the head loss, in meters, if f = 0.014. Round off to three decimal places. c. Compute the head loss, in meters, if C = 140. Round off to three decimal places.
Design a sanitary sewer to serve a population of5,000 people, if the average water consumptionis 400 liters per capita per day (lpcd). How manyextra persons can be served if the slope isdoubled? Using "n" value of 0.013 in theManning's formula & the return flow as 70%.Check the minimum self-cleaning velocity.Neglect infiltration & inflow?
Plz, solve all the parts of this problem. Use Excel sheet. Reg.No: 5395 Hydraulics A rectangular channel carrying 30 cfs has a bottom width of 4 ft. Manning roughness coefficient is 0.0a, where a = last digit of your registration number. Assume ten different depths of the flow and DEVELOP a specific energy diagram, using Excel sheet, for the given flow in this channel. Show (CLO3) 1) All the alternate depths and the corresponding energies. 2) The critical flow parameters. 3) Relationship between specific energy and the depth of flow for no velocity in a given channel
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
Given the following conditions: air permeability (k) = 10−7 cm2, radius of extraction well (Rw) = 5.1 cm, radius of vacuum influence (RI) = 12 m, vacuum pressure (Pw)=0.90atm (i.e., 9.09×105g/cm-s2), and air viscosity = 1.8 × 10−4 g/cm-s. (a) Find the airflow rate per unit thickness of well screen Q/H by using graphical solution and applying equation solution to verify. (b) If the well is screened to the entire contaminated zone of 5 m, what is the airflow rate in cfm? Does this flow fall in the ideal range of 100–1000 cfm?
In a basin irrigation machine, infiltration equation is Z=6T0.five (T as min and Z as millimeter), discharge in width unit is 0.000286 cubic meters in line with 2nd per meter, to be had discharge for irrigation is zero.00283 cubic meters per 2nd, there isn't runoff, basin width is 6 meters, requirement powerful storage in root depth is a hundred millimeters, and final infiltration after 4 hours (whilst water attain to the stop of basin) is 10 millimeters in keeping with hour. determine duration of basin, irrigation time, and common deep percolation.
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Water flows in a 3.0-m wide rectangular channel at Q = 20 m3/s and d1 = 1.5 m. If the flowundergoes a hydraulic jump, calculate:a) depth after the jump, d2;b) velocity before and after the jump;c) Froude number after the jump Fr2;d) head loss, hL and percent dissipation of energy.
In the context of a sewer system, you need to find the optimal diameter (DD) of a pipe to meet a design flow rate (QdQd) and a maximum allowed flow depth percentage (y/Dy/D). Utilize the flow velocity equation: V = -2 * SQRT(8 * g * R * S) * LOG10((ks / (14.8 * R)) + (2.51 * μ / (4 * ρ * R * SQRT(8 * g * R * S))) Given: - Design flow rate (Qd): 4.12 m³/s - Pipe slope (S): 0.01 - Pipe roughness (ks): 1.50E-06 m - Maximum flow depth percentage (y/D): 85% - Fluid density (ρ): 999.1 kg/m³ - Fluid viscosity (μ): 1.14E-03 Pa*s - Acceleration due to gravity (g): 9.81 m/s² - Pipe diameter (D): 1.000 m
Given the flow net in the figure below, having k=5×10−3cmsec. Determine the following a. How high water will rise in piezometers at points a, b, c, d. b. Rate of seepage through flow channel II. c. Total rate of seepage Please answer this asap. For upvote. Thank you very much
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
Water flows in a trapezoidal channel 3m wide and has a side slope of 1 vertical to 2 horizontal. The bed slope is 1:5000 and depth of flow is 1.5m. Find the flowrate if Bain's constant is 0.109. ANSWER IMMEDIATELY