hons Example 10.12 A laminar boundary layer on a flat plate has a velocity distribution given by ()- u (2n - 2n3 + n“). Where n = At a location the boundary layer thickness is 1.6 cm and the %3D U. force stream velocity is 1.25 m/s. If u = 1.136 x 10-5 N-s/m2. Calculate the shear stress at that location.

hons Example 10.12 A laminar boundary layer on a flat plate has a velocity distribution given by ()- u (2n - 2n3 + n“). Where n = At a location the boundary layer thickness is 1.6 cm and the %3D U. force stream velocity is 1.25 m/s. If u = 1.136 x 10-5 N-s/m2. Calculate the shear stress at that location.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.24P: Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the...

See similar textbooks

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
a) Estimate the drag force on the plate. You may use the expression ?? = ∫ τ?dA b) When the flow becomes turbulent, we can approximate the velocity gradient at the wall as constant, ∂? ∂? = ?. If the total drag force is 300 N, find ?. c) When the fluid is heated to 90oC, the density drops slightly and the viscosity decreases a lot, and engineers observe that the equation, τ? = 0.0644??∞ 2 δ ? , becomes less accurate. Explain why this might occur (1-2 sentences).
Consider turbulent fl ow past a sharp, smooth fl at plate ofwidth b and length L. What percentage of the friction dragon the plate is carried by the rear half of the plate?
Calculate thickness of the boundary layer (in metre) under laminar flow condition when distance from the upstream edge is 2.15 metre and local Reynolds number is 3000. Write the final answer in the box below.
An 16-kg slab slides down a 25° inclined plane on a 4-mmthick film of SAE 30 oil at 15.6 °C; the contact area is0.3m2. Find the terminal velocity of the slab. Explain ur answer
a) Estimate the drag force on the plate. You may use the expression ?? = ∫ τ?d? b) When the flow becomes turbulent, we can approximate the velocity gradient at the wall as constant, ∂? ∂? = ?. If the total drag force is 300 N, find ?. c) When the fluid is heated to 90oC, the density drops slightly and the viscosity decreases a lot, and engineers observe that the equation, τ? = 0.0644??∞ 2 δ ? , becomes less accurate. Explain why this might occur (1-2 sentences)
Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the Reynolds number is above 2000. For the following species, determine the maximum value of the average 1D speed for which laminar flow will occur: a) Ne at 293 K where ?η is 313 ?μP and ?ρ = (PM)/(RT) through a 2.00 mm (id) pipe b) Liquid water at 293 K where ?η is 0.891 cP and ?ρ = 0.998 g/mL through a 2.00 mm (id) pipe *Re = (?ρ **d)/?η, where d is the diameter of the tube through which the fluid is flowing.
Local boundary layer effects, such as shear stress and heattransfer, are best correlated with local variables, rather usingdistance x from the leading edge. The momentum thicknessθ is often used as a length scale. Use the analysis of turbulentflat-plate flow to write local wall shear stress τw in terms ofdimensionless θ and compare with the formula recommendedby Schlichting: Cf ≈ 0.033 Reθ -0.268.
A gas at 20°C and 1 atm flow at 6 ft/s past a thin flat plate.At x = 3 ft, the boundary layer thickness is 0.052 ft.Assuming laminar flow, which of the gases in Table A.4 isthis likely to be?
Answer completely Show how the Darcy-Weisbach equation can be derived from the Hagen-Poiseuille equation through the introduction of the Reynolds number. What is the friction factor, f, equal to for flow at a laminar condition? What is it equal to in other regimes of flow?
Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7thpower law and determine the boundary layer thickness and displacementthickness. Compare the values with values calculated using laminar flowcorrelations. υ = 1 × 10−6m2/s.
Read the question carefully and give me right solutions with clear calculations. The air flows past a 1m diameter disk oriented normal to upstream flow at 6.8m/s. The pressure distribution on front of the disk is function of the radius, where p(r) = (25 − 100 r2 ) N/m2 , and the pressure acts uniformly on back side with suction pressure of pback = −22 P a. a. Determine the total drag force on the disk. b. Calculate the drag coefficient for the disk . (Density = 1.25 kg/m3 ).