19 A balanced three-phase voltage source, Van = 200/0° V rms, positive phase sequence, is connected to an unbalanced A load: ZAB= 60 + 10, Zgc = 30 + 130. ZCA 30-130 2. Find: (a) the three phasor line currents; (b) the power de- livered to each phase of the load; (c) the power provided by each phase of the 'BC source.

19 A balanced three-phase voltage source, Van = 200/0° V rms, positive phase sequence, is connected to an unbalanced A load: ZAB= 60 + 10, Zgc = 30 + 130. ZCA 30-130 2. Find: (a) the three phasor line currents; (b) the power de- livered to each phase of the load; (c) the power provided by each phase of the 'BC source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24MCQ: Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line...

See similar textbooks

Similar questions

Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
In a balanced 3-phase system, the effective value of the IbB current for a triangular connected load is known as 15 (-150 degrees) Amperes and the effective value of the VCA voltage is known as 60 (90 degrees) Volts. Since it is known that the phase sequence is positive; Phase current IAB= 8.660 (60 degrees) A Phase current IAC= [Select ] Load impedance Z= [Select ] the total average power sent to the 3 phase load is Pt Aggregate= [Select ] (Note: Perform your operations using at least 3 digits after the comma.)
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. a) Draw the single-phase equivalent circuit and label all given quantities numerically. b) Calculatethe rms line (phase) current phasor in each phase. c) Calculate the total active or real power supplied by the source. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
Let the three-phase electrical system be illustrated in Figure . Knowing that its phase sequence is ABC and that Vcb=380∠135°V, determine the following: a) The value of the line currents demanded by each of the loads and supplied by the source. b) The power and power factor of each load and source. c) The power of the capacitor bank that must be installed to correct the power factor to 0.95 lagging. d) The currents supplied by the source after installing the capacitor bank. e) The percentage reduction of the total apparent power supplied by the source after installing the capacitor bank.
A three-phase, 3-wires CBA System alternator, sending 3-phase voltages of 339.4 volt to the lines, having a delta connected load, with VCA is the reference vector. ZBC = 12.99 – j7.5 ZCA = 8.66 + j5 ZAB = 10 + j0 Determine the phase and line current b) draw the phasor diagram and c) true power generates by the generator neglect the line losses.
A 3- phase star connected load has resistance of 10 Ω, inductance of 15.9mH & a capacitive reactance of 8 Ω respectively in R, B & Y phases. If the voltage between line and neutral line is 231V, 50Hz supply, Assume RYB sequence.Calculate the neutral current and Draw the current & voltage phasors.
S.4) the length of a three-phase power transmission line with a Nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/km. From the end of the line, a 56 MW star connected load is fed with a power coefficient of 0.8 back under a 64 kV interphase voltage. If the line head voltage of the transmission line is 69 kV, calculate the capacity and power of the star-connected capacitor to be shunted into the load connected to the end of the line.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, andadmittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. draw the circuit diagram