How many passes will it take to reduce the diameter from 5 % (five and one fourth) inches into 3 % (three andthree fourth) inch if the depth of cut is 1/16 inch.

Answered: Image /qna-images/answer/a4b67c84-60b9-4ffd-a21a-4a2da5483156.jpg

Answered: How many passes will it take to reduce…

How many passes will it take to reduce the diameter from 5 4 (five and one fourth) inches into 3 ¾ (three and three fourth) inch if the depth of cut is 1/16 inch.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.4: Manual Lathe Threading

Problem 9RQ: When threading, what is the reason for feeding the cutting tool at an angle for each depth cut?

See similar textbooks

Related questions

Q: You have a cube, 1.0 meter on a side. It is submerged in a fluid of density of 1500 kg/m³. One side…

Q: The pressure upstream of a normal shock wave is 1 atm. The pressure and temperature downstream of…

Q: For a point under a plane state of stress, the stresses on the vertical and horizontal planes are…

Q: A cold air-standard Otto cycle has a compression ratio of 12 and the temperature and pressure at the…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are…

Q: You have been selected by an engineer for them to design their newest robotic prototype. As of this…

A: The first version of any machine, including robots, is called a prototype. Following the creation…

Q: M1 = 2.6 5° %3D C A symmetric diamond-wedge airfoil is in an external flow at Mach number M1 = 2.6…

A: Given /c =tantc=tan450m1=2.6v=1.4from θ-β-M…

Q: Why does the shape of the passenger cabin windows on modern airplanes are rounded or elliptical? Why…

A: Given question: Why does the shape of the passenger cabin windows on modern airplanes are rounded or…

Q: What is the difference between modal and nonmodal G codes?

Q: 3. In the figure below, the coefficient of sliding friction for all contact surfaces is 0.20. When…

Q: A 37.5-mm-diameter rod 6 m long elongates 12 mm under a load 236 KN. The diameter of the rod…

Q: . A simple saturated refrigeration cycle for R-12 system operates at an evaporating temperature of…

Q: A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a…

A: The free-body diagram of the bar is as shown below,…

Q: QUESTION 82 When a force is applied to a substance, the substance will change its' shape, when the…

A: What is the plastic behavior of substance.

Q: A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section…

Q: At a given instant the wheel of radius r = 0.3 m is rotating with angular velocity w = 4 rad/s and…

Q: Pump Horsepower in Brine System. A pump pumps 0.200 ft3/s of brine solution having a density of 1.15…

A: Given DataQ=200 ft3/sρ=1.15 g/cm3∑F=18 ft lbf/lbm=57.9 ft2/sη=70%H=75ftg=32.15ft/s2

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

Q: How much heat is in 30 kg of 90% dry steam at 1 250 kPa?

A: Dryness fraction is given 90% or 0.9 Find , heat or enthalpy at this point

Q: 1. In a biological reactor of Volume m compressed air pressure increases from 1.5 bar (Pin) to…

A: Compressor is a device which intakes fluid and increases it pressure decrease the volume etc. The…

Q: The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r= 0.5 m.…

A: Givenm=27kgko=260mmr=0.5mF=354Nθ=6ot=3.2sg=9.81m/s2

Q: Air flows Steadily tnrough a thermally insulated duct of Varyıng Cross- Sechonal area . The air…

A: Given: The inlet temperature, T1 = 52°C The exit temperature, T2 = 77°C The inlet pressure, P1 = 200…

Q: A SYStem executes a power cycle while recieving 750 k) by heat transfer at a temperature of 1500°k…

A: GivenQ1=750kJT1=1500kQ2=-100kJT2=500KQ3=?T3=1000K

Q: Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the…

Q: A student pilot taxiing a Cessna 172- Skyhawk is brought to a full stop with a total distance of…

A: Givend=450mV=18knots=9.26 m/smpilot=170lbs=77.1107kgmairplane=757kg

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: 0. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the…

A: Given: The moment of inertia, I = 0.04 kg.m^2 The rotation rate, N = 45000 rpm The mass of car, m =…

Q: Determine the unit weight of air at 480 kPa absolute and 21°C

Q: A 5 m of ship model is towed in the water of kinemetic viscosity 1x10^-6 m^2/s at 3.5 m/s. The…

Q: Question 5: The following 0.8" diameter steel bar has three loads applied, as shown. Assuming that…

A: Find the stress at point A,B and C and total elongation of the bar.

Q: A- What is the system which used in Lorry braking ?, what is the advantages and dis advantages of…

A: Given question:What is the system which is used in Lorry braking? What is the advantage and…

Q: A 283-MW steam power plant operates on the Rankine cycle but with turbine and pump efficiencies of…

A: GivenP1=10000 kPa=10MpaT1=550oCP2=50kPaηP=ηT=90%Power=282 MW

Q: A beam of length L = 22 in supports a load which varies from w = 20 lb per ft at the right end to…

A: Find the position of resultant force from left end for the triangular load.

Q: An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per…

A: Given data Industrial tank discharges water through a 5 inch nozzle at 5 m/s Diameter of nozzle = 5…

Q: 7. Calculate the displacement at the free end of the inclined beam shown in Figure P3.7.Repeat the…

Q: A Carnot engine operating between 775 K and 305 K produces 51.18 Btu of work. Calculate the heat…

Q: 3. The 4 kg box shown in the figure start from rest at t = 0 in which the friction is negligible.…

Q: Determine the surface tension of liquid in contact with air and a glass tube. If the capillary tube…

A: Find the surface tension.

Q: In a lake, two boats A and B are leaving Station1 at the same time, Boat A is directed straight to…

A: Given data Velocity of Boat A = 7 m/sBoat B is travelling in the North west direction .Time taken by…

Q: Q1: design LQR for single link flexible joint robot manipulator with (k=1, Bm=0.02 Nms/rad, Jm=0.003…

Q: 10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were…

A: Given: Number of rivets→n=10 Diameter of the each rivet→d=1.25 inch Hence area for shear…

Q: Identify the description with Material handling Principles: 12. Planning 13. System Flow 14.…

A: In this problem, we have to answer 15,16 and 17 as per the ask. In this we have to identify the…

Q: Determine the external reactions at A and F for the roof truss loaded as shown. The vertical loads…

Q: A scuba tank is being designed for an internal pressure of 2,685 psi with a factor of safety of 2.0…

Q: Q4) A) A radial, multistage, four impellers, keyed to the same shaft, centrifugal pump is…

Q: At the Niagara Falls generating station, the water drops 102 m from the intake pipes at the top of…

A: Given data Height (H) = 102 m Mass flow rate (m˙) = 1000 kg/s Efficiency of the turbine (η) = 75% =…

Q: 1. A 75 m high wind tower with a 50 m rotor diameter has been constructed in a region that follows…

A: Given: The height of wind tower, H = 50 m The diameter of rotor, d = 50 m The coefficient of shear…

Q: Josh threw the marble vertically upward with a speed of 70 ft/s from a bridge. On the way down, the…

A: Find Height of the bridge

Q: The cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at…

Q: Consider a two-degrees-of-treedom system shown below What is the amplitude of vibration of mass 2 at…

A: A system with two degrees of freedom requires two coordinates to fully express its equation of…

Q: At what rpm should the lathe revolve to rough turn a piece of cast iron (CS = 60 SFPM) 51 mm in…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

How many passes will it take to reduce the diameter from 5 % (five and one fourth) inches into 3 % (three and
three fourth) inch if the depth of cut is 1/16 inch.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If a 0.050" depth of cut is taken on the diameter of a workpiece, by how much will the diameter be reduced?
__________ uses a high-pressure stream of water containing abrasive particles to cut material.
By decreasing the feed: a)Depth of cut will be decrease b)Nose radius will increase c)Roughness of surface will increase d)Flatness of surface will increase
what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25 feet?
what is the right anwer and solution for the total distance?
How long will it take to saw a rectangular piece of aluminum plate 8 inches wide and 1.5 inch thick if the length of the cut is 8 inches, the power hacksaw makes 120 rev/min and average feed per stroke is 0.0060 inch?
Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut is Axial force Tangential force Radial force
In a milling machine the distance the workpiece advances under the cutter is known as Select one: a Cutting speed b. Thickness c Depth of cut d. Feed
By increasing the feed: A ) Roughness of surface will decrease B) Nose radius will decrease C) Depth of cut will increase D) Flatness of surface will decrease
What two terms refer to the squareness of a cut?
Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the sentence incorrect and write its corresponding correct answer. 16. since the thickness of chips is always greater than the depth of cut, chip compression ratio is àways less than 1.0. 17. Inserts have multiple cutting points. 18. Free Machining steels are non-ferrous metals which contain sulfur and phosphorus.
Determine the number of strokes per minute at which the shaper should run to machine a piece of copper having a cutting speed of 80 feet per minute and with stroke adjusted to 6 inches.