How much heat is lost due to heat convection in a 25 minute period from 50*10ft wall. If the difference between the wall temperature and the air temperature is 54 F and the surface of the wall has a heat transfer ratio of 0.17 BTU/hr? Show detailed solution

How much heat is lost due to heat convection in a 25 minute period from 50*10ft wall. If the difference between the wall temperature and the air temperature is 54 F and the surface of the wall has a heat transfer ratio of 0.17 BTU/hr? Show detailed solution

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.18P: The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide...

See similar textbooks

Related questions

Q: QUESTION 4 Length of the culvert is a factor that affects flow through a culvert O True O False

A: For underway steam carrying culvert will be used. It's a tunnel structure.

Q: A 12 cm thick wall has a thermal diffusivity of 1.5 x 10-6 m2/s and initially a uniform temperature…

A: Assume that one dimensional and divide 0.12 m thick wall into 4 equal parts each having 0.03 m…

Q: To correct the vision of a hyperopic eye, a corrective lens should enable the wearer to focus or…

A: we will demonstrate the condition for a hypermetropia eye.

Q: Determine the rated speed of a highway curve of radius = 120 m banked through an angle = 180 . The…

Q: Determine the velocity of the aircraft flying at 2500 m, when the dynamic pressure is 45N/m^2?…

Q: Problem 2 Design of Shear Members A cantilever beam has a span of 3 m. The beam carries a uniform…

Q: 6-7. Water flows through the hose with a velocity of 4 m/s. Determine the force that the water…

Q: Bar AB rotates as shown with an angular velocity equal to 1O rad/s. Assume AB ha a length of 500mm…

Q: Two cars start from rest and race down parallel lanes of a straight track. Vehicle A accelerates at…

Q: A tall glass cylinder is filled with a layer of water 18.0 cm deep, and floating on top of the…

Q: Q3/ A mass suspended from a helical spring vibrate in a viscous fluid medium whose resistance varies…

Q: Determine the diameter of the bolts used in rigid flange coupling if transmitted torque is 270N-m,…

Q: In the following unit cell, which vector represents the [001] direction?

Q: Find the height H without any leak.

Q: 2kN/m 3- The nails are on both sides of the beam and each can resist a shear of 2 kN. In addition to…

Q: Problem 7.10 A thin circular disc of uniform thickness and of radius b is built up of two concentric…

A: A thin circular disc of uniform thickness and radius b is made up of two concentric parts, with a…

Q: 1- Using a conservation of momentum equation, show that the force on the hemispherical vane is twice…

Q: 8-A diesel engine has a clearance volume is 0.00025m³ and bore and stroke of 152.5mm and 200mm,…

A: Given that, Clearance volume, Vc=V2=0.00025 m3Bore, D=152.5 mm,Stroke, L=200 mm,Pressure of air,…

Q: Here, there is a human powered submarine. The length of the submarine is 4.85 m and the hope is it…

A: Equate Reynold's number of the model and the submarine. ρpvpLpμp=ρmvmLmμm Here, ρp is the density of…

Q: Hot water (specific heat of 4.18 Kj/kgK) at 66C is flowing through a metal pipe (6 m long, 2 cm ID,…

A: Given Hot water is flowing through a metal pipe. Specific heat of water = 4.18 Kj/KgK Temperature…

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a Поог. The…

Q: 1-prove tha the air standard Iiciency of an engine Wörking on the constant 1 Calculate the air…

Q: Calculate the ranges of typical machining times for face milling a 250-mm-long workpiece with a…

A: Given DataD=50mmn=10teethd=25mmL=250mm

Q: The figure shows the cross section of a circular steel tube that is filled with concrete and topped…

Q: A homogeneous 950 kg bar AB is supported at either end by a cable as shown in the figure below.…

Q: Air enters a multistage compressor of a jet engine at 0.65 atm and 275 K with a flow rate of 63.5…

Q: Find the strain original length=100 mm Change in length3D0.05 mm

Q: Problem 3 Draw the shear and bending-moment diagrams for the beam. 4 kN M = 2 kN m A -2 m -2 m 2 m

Q: For the frame shown, the wood has a normal failure stress of 42 MPa, and a shear failure stress of…

A: Given DataNormal failure stressσf=42MPashear failure stressσfs=10MpaLoadP=40kNFactor of safetyFOS=2

Q: GIVEN A thin rectangular plate having a width w and a heigh h is located so that it is normal to a…

Q: Qr) Find the stress distribution at the section ABCD for the block shown in the figure. Sketch the…

Q: 3- The nails are on both sides of the beam and each can resist a shear of 2 kN. In addition to the…

A: When a structure, such as a beam, is subjected to a transverse shear force, the bending normal…

Q: > View Available Hint(s) Learning Goal: To understand the concept of moment of a force and how to…

Q: 1. A centrifugal fan is delivering 2000 cfm of air at a total pressure differential of 2 in.w. The…

A: Dear student, According to the guidelines I am allowed to answer only three…

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: Given: P = 10 kW N = 400 rpm Shear Stress = 40 MPa

Q: 5) A wedge airfoil is placed in a supersonic flow at M 2. G. Calculate the lift and drag…

A: Given: The Mach number, M = 2.G = 2.2 The angle of attack, α = 4°

Q: Q.2 A square timber beam used as a railroad tie is supported by a uniformly distributed loads and…

A: Given: ununiform distributed load→W1=24 KN and W2=48 KN Hence upward uniform distributed load:…

Q: A crawler crane will be located on a temporary work platform. The total resultant vertical load due…

A: To find the maximum angle of the wrecking ball going to be at the maximum height at which all…

Q: A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of…

A: Given: Diameter of the reinforced concrete column→D=400 mm So total area of the…

Q: 3 identical blocks shown in figure. If A and C are moving together at 12m/sec and B is at rest when…

A: Given: All the blocks are identical so let us assume the mass of each block is m. Initial velocity…

Q: Derive the Clausius Clapeyron Equation Thermodynamics and show it step by step

Q: The angel between OS and the horizontal is 160 degrees. please draw the velocity diagram and the…

A: Given: speed of the crank OS→N=180 rpm Hence rotational speed of the crank…

Q: A fillet weld is used to join 2 medium carbon steel plates each having a thickness of 5.0 mm. The…

Q: A ball is thrown vertically upward from the top of a 30-m high building with an initial velocity of…

Q: 2- An internal combustion engine has a bore of 200 mm and stroke of 380 mm. The clearance volume is…

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N For the given triangle, missing angle θ can be found by,…

Q: Q/ At the commencement of the compression stroke, the cylinder of an oil engine is charged with air…

A: Given dataP1 = 96.5 kPaT1 = 65 °C V1/V2 = 14Compression follows PV1.35 = CMass of fuel injected =…

Q: Identify the following as Attribute or Variable data. (A or V) Percent absenteeism Number of…

Q: Assuming a constant failure rate of 0.012 with an exponential probability distribution, if only a…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
How much heat is lost due to heat convection in a 25 minute period from 50*10ft wall. If the difference between the wall temperature and the air temperature is 54 F and the surface of the wall has a heat transfer ratio of 0.17 BTU/hr? Show a Schematic Diagram
The hot water pipe of a heating system, 20 m long and 8 cm in diameter, was buried 80 cm below the soil surface. The outer surface temperature of the pipe is 60 °C. Find the heat loss rate in the pipe by taking the surface temperature of the soil as 5°C and the thermal conductivity of the soil at that location as 0.9 W/m°C.