1 please 1 a) Design a noninverting amplifier with a gain of 100 using ideal op amps and practicalvalues of resistors. Draw a schematic of your circuit showing input, output, and allresistor values.b) If the op amp in part la) is not ideal but has an input offset voltage of +/- 5mV andinput bias currents of 100nA and the source resistance at the input is 50k ohms, then whatis the range of the output voltage when the input is zero volts? Show and explain ourcalculations.2 a) Calculate the output voltage in the circuit below using superposition. Assume thatthe op amps are ideal and that Va-50mV and Vb-30mV.b) What is common mode rejection ratio (CMRR) and why is it important?c) If the circuit below has 80dB of CMRR and there is IV of common mode signal, thenhow much of the common mode signal will be present at the output?20KakLOK3. Find the output voltage v, in each of the 3 circuits below and explain how you found it.Assume all op amps are ideal.NoIDK100ml10K3100,jok10 ml10k20kwww20kMELONEN₂10K20-Vd. Draw the circuit diagram for the 3 op amp instrumentation amplifier and show appropriatevalues for all the resistors so that the amplification of differential signals is 100.e. What is the primary advantage of this configuration and what is required of the resistors inorder to achieve this benefic? Why is this benefit essential to the practical problem of amplifyingreal transducer signals?f. If the input voltage is set to zero in the circuit of b, what is the maximum range of the outputvoltage if the input offset voltage maximum value is +/- 8mV and the input bias currentmaximum is 200 nanoamps?

Answered: Image /qna-images/answer/25570dee-60d8-48f9-bdbe-4c40f794c7a3.jpg

I a) Design a noninverting amplifier with a gain of 100 using ideal op amps and practical values of resistors. Draw a schematic of your circuit showing input, output, and all resistor values. b) If the op amp in part la) is not ideal but has an input offset voltage of +/- 5mV and input bias currents of 100nA and the source resistance at the input is 50k ohms, then what is the range of the output voltage when the input is zero volts? Show and explain our calculations.

I a) Design a noninverting amplifier with a gain of 100 using ideal op amps and practical values of resistors. Draw a schematic of your circuit showing input, output, and all resistor values. b) If the op amp in part la) is not ideal but has an input offset voltage of +/- 5mV and input bias currents of 100nA and the source resistance at the input is 50k ohms, then what is the range of the output voltage when the input is zero volts? Show and explain our calculations.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

1. Find the Thévenin equivalent circuit with respect to the output terminals a, b for the inverting amplifier shown. The dc signal source has a value of 880 mV. The op amp has an input resistance of 500 kΩ, an output resistance of 2 kΩ, and an openloop gain of 100,000. 2. What is the output resistance of the inverting amplifier? 3. What is the resistance (in ohms) seen by the signal source vs when the load at the terminals a, b is 330 Ω?
An amplifier is formed by cascading the three operational amplifier stages as shown. What are the voltage gain, input resistance, and outputresistance for this amplifier (a) if the op amps are ideal? (b) If the op amps have an open-loop gain of 94 dB, an input resistance of 400 kΩ, and an output resistance of 250 Ω?
A single-pole op amp has an open-loop gain of 92 dB and a unity-gain frequency of 1 MHz. What is the open-loop bandwidth of the op amp? (a) The op amp is used in a noninverting ampliﬁer designed to have an ideal gain of 32 dB. What is the bandwidth of the noninverting ampliﬁer? (b) Repeat for an inverting ampliﬁer with and ideal gain of 32dB.
Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
An amplifier is formed by cascading the two operational amplifier stages as shown. What are the voltage gain, input resistance, and outputresistance for this amplifier (a) if the op amps are ideal? (b) If the op amps have an open-loop gain of 106 dB, an input resistance of 300 kΩ, and an output resistance of 200 Ω? (c) Draw the new circuit and repeat (a) and (b) if the two amplifier stages are interchanged.
how do i design this op amps so that i can get an overall gain of -8? and how do i find the values of vin and vout? (resistors that may be used: 100,180,220,330,1k,2.2k,3.3k,4.7k,6.8k,10k,22k,33k,47k,68k,100k,180k,1.2M ohms)
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
Consider the following op amp configuration.(a) Choose R2 such that the ideal voltage gain is Av = 40dB and draw the amplifier’stransfer characteristic.(b) Find the amplifier’s input and output resistances.(c) If the op amp’s internal gain is Ao = 120dB, what is the expected voltage gain ofthe entire network?
Using the components listed below, design an amplifier having a voltage gain of −10 ± 20 percent. The input impedance is required to be as large as possible (ideally, an open circuit). Remember to use practical resistance values. Cascade a non-inverting stage with an inverting stage.1) Standard 5%-tolerance resistors.2) Standard 1%-tolerance resistors. (Don’t use these if a 5%-tolerance resistor will do, because 1%-tolerance resistors are more expensive.)3) Ideal op-amps.4) Adjustable resistors (trimmers) having maximum values ranging from 100 Ω to 1 MΩ in a 1–2–5 sequence (i.e., 100Ω, 200Ω, 500Ω, 1 kΩ, etc.). Don’t use trimmers if fixed resistors will suffice.
Derive the appropriate equation for an inverting amplifier with op-amp and provide the values of resistances to obtain the gain equal 3 (kvR -> infinity, Vr -> 0)
The op amp in the adder-subtractor circuit attached is ideal. A. Find the output voltage v0 given Va = 2V, Vb = 3V, Vc = 5v, Vd = 6V. B. For the values given in A, find V0 if the feedback resistor is replaced with a 100 ohm resistor.