I just need help drawing the KINEMATIC DIAGRAMand the GRAPHS (v-a, a-s, s-t, v-t, v-t, or a-t) if applicable. The v – s graph for a test vehicle is shown. (Figure 1)Part ADetermine its acceleration when s = 125 mExpress your answer to three significant figures and include the appropriate units.a = 13.9 "SubmitPrevious AnswersCorrectPart BFigure< 1 of 1>Determine its acceleration when s = 175 mExpress your answer to three significant figures and include the appropriate units.v (m/s)m.a = -25.0SubmitPrevious AnswersCorrect50Provide Feedbacks (m)150200

Given: The v-s diagram is shown below: From distance 0 to150 m, the equation of velocity line is…

Answered: I just need help drawing the KINEMATIC…

Engineering

Mechanical Engineering

I just need help drawing the KINEMATIC DIAGRAMand the GRAPHS (v-a, a-s, s-t, v-t, v-t, or a-t) if applicable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The acceleration of a particle traveling along a straight line is a = ¼ s1/2 m/s2 ,where s is in meters. If v = 0 m/s and s = 1 m when t = 0 s, determine the particle’s velocity at s =2 m.NOTE #1 – A sketch of the scenario should be created by you to enhance your work.NOTE #2 – A particle is rather uninspiring, yet they are suitable in learning engineering scienceprinciples. You are welcome to spice up this problem by replacing the particle with a rigid bodyof interest to you. You are welcome to comment on your answer how replacing abstract conceptswith tangible examples influences your learning of dynamics topics
11.2 The displacement of a particle is given by s = 2t3 - 43t2 + 118t - 64 where s is in feet and t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 19 seconds of motion. After you have made the plots, answer the questions.
In a physics lab experiment, you release a small steelball at various heights above the ground and measure the ball’s speedjust before it strikes the ground. You plot your data on a graph that hasthe release height (in meters) on the vertical axis and the square of thefinal speed (in m2/s2) on the horizontal axis. In this graph your datapoints lie close to a straight line. (a) Using g = 9.80 m/s2 and ignoringthe effect of air resistance, what is the numerical value of the slope ofthis straight line? (Include the correct units.) The presence of air resistancereduces the magnitude of the downward acceleration, and the effectof air resistance increases as the speed of the object increases. Yourepeat the experiment, but this time with a tennis ball as the object beingdropped. Air resistance now has a noticeable effect on the data. (b) Isthe final speed for a given release height higher than, lower than, or thesame as when you ignored air resistance? (c) Is the graph of the releaseheight…
The position of a particle is given by s = 0.27t3 - 0.76t2 - 2.44t + 5.13, where s is in feet and the time t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 9 seconds of motion. After you have the plots, answer the questions as a check on your work.
Q1. A driver enters a curved car at 72 km/h, slows down, causing the speed to drop at a steady rate of 4.5 km/h every second. If the radius of curvature is 16.7 m. Find the acceleration of the car after 4 seconds from the driver starting to slow down.
15. An automobile is traveling at 25 m/s. It takes 0.3 sec to apply the brake after which the deceleration is 6 m/s2. How far does the automobile travel before it stops? ANS: 60m 17. Water drips from a faucet at uniform rate of 3 drops per second. Find the distance between 2 successive drops if the upper drop has been in motion ¼ second. ANS: 1.36 m 20. A skier is filmed by a motion picture photographer who notices him traveling down a ski run. The skier travels 36 m during the fourth second of the filming and 48 m during the sixth second. What distance did he cover in the eight seconds of filming? Assume that the acceleration is uniform throughout. ANS: 312 m
Problem: A particle is moving along a straight line such that its position is given by s=(4t−t2)ft, where t is in seconds. Question 1: Determine the distance traveled from t=0 to t=5s Express your answer to three significant figures and include the appropriate units. Question 2: Determine the average velocity of the particle during this time interval. Express your answer to three significant figures and include the appropriate units. please answer both of these with the correct answer
Problem: A particle is moving along a straight line such that its position is given by s=(4t−t2)fts=(4t−t2)ft, where tt is in seconds. Question: Determine the average velocity of the particle during this time interval. Express your answer to three significant figures and include the appropriate units.
An aircraft touches down at a speed of 200 km/hour and the brakes are applied. If the aircraft deceleration is given by ? = −0.05 ? (using units of metres and seconds), how far will it have travelled along the runway by the time its speed drops to 20 km/hour?
A particle moves along a straight line in such a manner that its displacement, at any instant, from a fixed point on its path is given by the question s = 1/10 + (?^3 + 6t^2 + −4 ?)What displacement, velocity and acceleration will the particle attain after 10 seconds?
A body moves along a linear path and its rate of change of velocity varies with time and is written as a=2-3t, where t is the time in second. After 5 second, from start of observation its velocity is determined to be 20 m/s. After 10 second from start of observation, the body is at 85 m far from the origin. Determine the following:a. Rate of change of velocity and velocity at the start of motion.b. Distance from the origin at the start of observationc. Time after start of observation in which the velocity becomes zero.
An electric car is subjected to acceleration tests along a straight and level test track. The resulting v-t data are closely modeled over the first 10 seconds by the function v = 24t - t2 +5t1/2, where t is the time in seconds and v is the velocity in feet per second. Determine the displacement s as a function of time over the interval 0 ≤ t ≤ 10 sec and specify its value at the indicated times.