Show all working explaining detailly each stepAnswer must be typewritten with a computer keyboard!Answer Qi, ii 4. A smooth sphere P moves on a horizontal table and collides with an identical sphere Qat rest.At impact, the direction of motion of Pmakes an angle of 45° with the line of centres of thespheres. Given that the coefficient of restitution between the spheres is e and that after impact,the direction of motion of P makes an acute angle e with the line of centres of the spheres,show that(i)tane =(ii)0< cotoGiven that each sphere is of mass m and that the speed of P before impact is U,(iii)find the loss in kinetic energy due to the impact.

Answered: Image /qna-images/answer/babca44f-3e12-41ae-aec9-e1844773283a.jpg

Answered: (i) tane (ii) 0< coto Given that each…

(i) tane (ii) 0< coto Given that each sphere is of mass m and that the speed of P before impact isU, (iii) find the loss in kinetic energy due to the impact.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three spheres, each with a mass of m , can slide freely on a frictionless, horizontal surface. Spheres A and B are attached to an inextensible, inelastic cord with a length I and are at rest in the position shown when sphere B is struck squarely by sphere C , which is moving with a velocity v0 . Knowing that the cord is taut when sphere B is struck by sphere C and assuming perfectly elastic impact between B and C , and thus the conservation of energy for the entire system, determine the velocity of each sphere immediately after impact.
A thin circular rod is supported in a vertical plane by a bracket at A. Attached to the bracket and loosely wound around the rod is a spring of constant k= 3 lb/ft and undeformed length equal to the arc of circle AB. An 8-oz collar C , not attached to the spring, can slide without friction along the rod. Knowing that the collar is released from rest at an angle 0 with the vertical, determine (a) the smallest value of 0 for which the collar will pass through D and reach point A, (b) the velocity of the collar as it reaches point A.
A 20-g bullet is fired at a 5-kg square panel of side b = 300 mm. The velocity of the bullet just before the collision is 500 m/s, with θθ = 15°, and is embedded into the plate after impact with a duration of 2.5 × 10-3 seconds. Knowing that the horizontal component of the impulsive reaction at A is zero, what is the value of the impulsive reaction at the support at A?
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Two spheres A and B (of mass m each) were fired vertically from the ground with different initial velocities at different times. When sphere A reached its summit, sphere B, with an upward velocity of 10.76 m/s, created a head-on collision with A. The impact caused sphere A to break into two pieces, each of mass m/2. Knowing one-piece reached Point C and the other piece reached point D after the collision, determine: (a) the velocity of sphere B after the collision; (b) the angle θ and the speeds of the two pieces after the collision; and (c) the force exerted by sphere A on B if the collision occurred in 0.001s.
A uniform slender bar of length L = 200 mm and mass m = 0.5 kg is supported by a frictionless horizontal table. Initially the bar is spinning about its mass center G with a constant angular speed w1 = 6 rad/s. Suddenly latch D is moved to the right and is struck by end A of the bar. Knowing that the coefficient of restitution between A and D is e= 0.6, determine the angular velocity of the bar and the velocity of its mass center immediately after the impact.
A 30-g bullet is fired with a horizontal velocity of 450 m/s and becomes embedded in block B , which has a mass of 3 kg. After the impact, block B slides on 30-kg carrier C until it impacts the end of the carrier. Knowing the impact between B and C is perfectly plastic and the coefficient of kinetic friction between B and C is 0.2, determine (a) the velocity of the bullet and B after the first impact, (b) the final velocity of the carrier.
The slender rod AB of length L = 1 m forms an angle β = 30° with the vertical as it strikes the frictionless surface shown with a vertical velocity v1=2 m/s and no angular velocity. Knowing that the coefficient of restitution between the rod and the ground is e = 0.8, determine the angular velocity of the rod immediately after the impact.
NEED WITHIN 1HR THANKS 4.A 1.3-lb sphere A is dropped from a height of 1.8 ft onto 2.6-lb plate B, which is supported by a nested set of springs and is initially at rest. Knowing that the set of springs is equivalent to a single spring of constant k = 5 lb/in., determine the value of the coefficient of restitution between the sphere and the plate for which the height h reached by the sphere after rebound is maximum, the corresponding value of h, and the corresponding value of the maximum deflection of the plate.
A 10-lb collar is attached to a spring and slides without friction along a fixed rod in a vertical plane. The spring has an undeformed length of 14 in. and a constant k= 4 lb/in. Knowing that the collar is released from rest in the position shown, determine the force exerted by the rod on the collar at (a) point A, (b) point B. Both these points are on the curved portion of the rod.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. In the system shown, a 150 N collar-pulley assembly slides on a horizontal shaft with coefficient of kinetic friction μk = 0.10 between the collar and the shaft, and is acted upon by a force P with a magnitude of P = 253.5 N at an angle θ = 30.35° as shown. Knowing that the assembly is initially at rest, what is the time when the velocity reaches to 3 m/s? Also, at this instant, find the tension in the cord and the velocity of block A.
A 7.5-lb collar is released from rest in the position shown, slides down the inclined rod, and compresses the spring. The direction of motion is reversed and the collar slides up the rod. Knowing that the maximum deflection of the spring is 5 in., determine (a) the coefficient of kinetic friction between the collar and the rod, (b) the maximum speed of the collar.
A 1-oz bullet is fired with a horizontal velocity of 750 mi/h into the 18-lb wooden beam AB. The beam is suspended from a collar of negligible mass that can slide along a horizontal rod. Neglecting friction between the collar and the rod, determine the maximum angle of rotation of the beam during its subsequent motion.