If a deflection of 13 degrees in a pressure transducer is produced by apressure of 3 bar, the scale deflection of the instrument is:0.231 bar/degree.0.231 degree/bar.O 4.333 degree/bar.O 4.333 bar/degree.Not all of the above.The resolution of a digital voltmeter that has 16 – bit accuracy with therange of 250V is equal to:3.5mv.1.7mv.1.8mv.1.9mv.Not all of the above.

1) given deflection in degree= 13 Pressure is 3 bar 2) no of bits n= 16 V range = 250v

If a deflection of 13 degrees in a pressure transducer is produced by a pressure of 3 bar, the scale deflection of the instrument is: 0.231 bar/degree. 0.231 degree/bar. 4.333 degree/bar. 4.333 bar/degree. Not all of the above. The resolution of a digital voltmeter that has 16 – bit accuracy with the range of 250V is equal to: 3.5mv. O 1.7mv. 1.8mv. 1.9mv. O Not all of the above.

If a deflection of 13 degrees in a pressure transducer is produced by a pressure of 3 bar, the scale deflection of the instrument is: 0.231 bar/degree. 0.231 degree/bar. 4.333 degree/bar. 4.333 bar/degree. Not all of the above. The resolution of a digital voltmeter that has 16 – bit accuracy with the range of 250V is equal to: 3.5mv. O 1.7mv. 1.8mv. 1.9mv. O Not all of the above.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q: Find the digital equivalent and the resolution for a 3 bit DAC using Successive Approximation of Vin = 0.4 V and Vref = 1 V?
Please assist with question 3, details on how to do. Thank you. Check image for Q3 3. Figure shows a PCM signal in which the amplitude levels of volt and volt are used to represent binary symbols 1 and 0, respectively. The code word used consists of three bits. Find the sampled version of an analog signal from which this PCM signal is derived.
Answer as quickly as possible. I'll give upvote. Thank you. The circuit shown is a common source amplifier with a current mirror bias. It is given that the NMOS (M1) parameters are μoCox = 3mA/V2, VTH,n = 0.5V and λ = 0.02 and the PMOS (M2 and M3) parameters are μoCox = 1mA/V2 and VTH,p = −0.6V . The PMOS transistor M3 does not have channel length modulation while PMOS transistor M2 has λ = 0.02. It is also given that the dimensions of M2 and M3 have equal widths of 5µm and lengths of L2 = 3µm and L3 = 1.5µm, respectively. M1 has length of L1 = 1µm and width of W1 = 2µm. Find the gm and ro of transistor M1.
For 4.3 V, calculate is the digital output by using a Successive-Approximation ADC method? Also calculate the error. (10-bit A/D with range 0V – 10V)
A temperature between 51°C and 264 °C is converted into a 0- to 5.0- V signal. This signal is fed to an 8-bit ADC with a 5.0-V reference. What is the actual measurement range of the system? a. What is the resolution? b. What is the maximum quantization error? c. What hex output results from 169 °C? d. What temperature does a hex output of C5H represent?
(Analog to Digital signal conversion problem) Continuous voltage is converted to discrete signal: Range of signal after amplification= 0V to 5 V A/D converter = 6 bits # Quantization levels = 26 = 64 Question: Assume the input signal is 3.5 V. Use the successive approximation method to encode the signal for this 6-bit converter. Please write both the decimal value and binary value for the code
1. How many resistors and switches would be required to implement a 6-bitresistor-string DAC? ResourcesStudents 2. Find output voltage and current for a binary-weighted resistor DAC of 4 bitswith given condition of R= 1kn, R = 5kN, VR = -12v and applied binaryword is 1101. 3. Find the voltage for an R-2R DAC of 4 bits with given condition of R = 6kNR, = 2kn, VR = 16v and applied binary word is 1011.
1. During the process of digital sampling, data can be lost due to aliasing.Analyse this problem and provide at least two possible solutions. Also,determine the rate at which a signal should be sampled, if the highestfrequency is 50MHz. (b) An 9-bit binary number is used to represent an analog value in the rangefrom -10oC to 100oC, determine the resolution of the system andinterprete your result.
A 10-bit D/A converter has a full-scale voltage of 2.5 V. What is the voltage corresponding to the LSB?Whatistheoutputvoltageifthebinaryinput code is equal to (0101100110)?
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
Refer to a modified common source amplifier below, please help me to find the input resistance, output resistance, and the voltage gain of the circuit. The parameters of the NMOS are given as: unCox = 0.065 (A/V2), the channel length modulation effect is 0.005 (1/V), W/L = 100um/100um, and the threshold voltage Vt = 1.25 (V). Hope you can show me how to calculate and explain everything in detail.
2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.