A temperature between 51°C and 264 °C is converted into a 0- to 5.0- V signal. This signal is fed to an 8-bit ADC with a 5.0-V reference. What is the actual measurement range of the system? a. What is the resolution? b. What is the maximum quantization error? c. What hex output results from 169 °C? d. What temperature does a hex output of C5H represent?

A temperature between 51°C and 264 °C is converted into a 0- to 5.0- V signal. This signal is fed to an 8-bit ADC with a 5.0-V reference. What is the actual measurement range of the system? a. What is the resolution? b. What is the maximum quantization error? c. What hex output results from 169 °C? d. What temperature does a hex output of C5H represent?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Given a 5-bit ADC with the following reference values Vref= -2V and 12V, what is the voltage represented by the output sequence 01010?
The current output of a successive approximative type ADC is showing as 110011. If the reference voltage to the ADC is 5V, what is the corresponding analog signal voltage input to this ADC? If the ADC were of 10 bits, would the conversion time be reduced? Please answer ASAP I will like it please ASAP...
A)What will be the frequency at C if the clock is 320 kHz? B) What is the modulo of the circuit? C) What is the output (in binary) after 737 pulses?
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
A 10-bit 5-V ADC operates with a sampling frequency of 1 MHz. If a linear histogram test is to be conducted on this ADC with a ramp signal of 15-ms duration, estimate the voltage resolution of this test.
Q1.A) If an 8-bit SAR ADC is used to digitize 8V full scale signal, what will be the digital o/p for an analog i/p of 5.76 V (perform complete analysis)?
An A/D converter uses 14-bit numbers and has a voltage range between +6V to -6V. ( Use 2 decimal places) a) What is the dynamic ratio of the system in dB? b) Find resolution of digitalization in μV that is expressed as the smallest voltage increment?
1. How many resistors and switches would be required to implement a 6-bitresistor-string DAC? ResourcesStudents 2. Find output voltage and current for a binary-weighted resistor DAC of 4 bitswith given condition of R= 1kn, R = 5kN, VR = -12v and applied binaryword is 1101. 3. Find the voltage for an R-2R DAC of 4 bits with given condition of R = 6kNR, = 2kn, VR = 16v and applied binary word is 1011.
WHAT IS THE MODULO OF THE CIRCUIT? WHAT IS THE OUTPUT (IN BINARY) AFTER 738 PULSES?
A 12-bit D/A converter has VREF = 5.12 V. What is the output voltage for a binary input code of (101010101010)? What is VLSB? What is the size of the MSB?
How to measure the quality of the output signal in ADC? A. Signal-to-noise ratio B. Quantization error C. Signal-to-quantization-noise ratio D. Bit error rate
(II) Consider a rather coarse 4-bit analog-to-digital conversion where the maximum voltage is 5.0 V. (a) What voltage does 1011 represent? (b) What is the 4-bit representation for 2.0 V?