If a load of 60 kN is applied to a rigid bar suspended by 3 wires as shown in the above figure what force will be resisted by each wire? The outside wires are of Al, cross- sectional area 300 mm² and length 4 m. The central wire is steel with area 200 mm² and length 8 m Initially there is no slack in the wires E= 2x105 N/mm2 for Steel = 0.667 x 105 N/mm² for Aluminum 60 KN Alum, wires Steel wire

If a load of 60 kN is applied to a rigid bar suspended by 3 wires as shown in the above figure what force will be resisted by each wire? The outside wires are of Al, cross- sectional area 300 mm² and length 4 m. The central wire is steel with area 200 mm² and length 8 m Initially there is no slack in the wires E= 2x105 N/mm2 for Steel = 0.667 x 105 N/mm² for Aluminum 60 KN Alum, wires Steel wire

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a fixed bearing in A and a roller bearing in B. The steel is loaded with a point load, P, in the middle. The maximum permissible normal stress is oy = 200 MPa. Cross section: s9 S8 54 53 55 s1 S7 d = 40 mm S2 S6 1m 1m 1 m 1 m a) Calculate the rod forces. Express the answers with P, and state whether they are stretched or pressed. Is there any zero spells? b) Determine how large the load P can be without material breakage or buckling the spells. 3 m
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is - A 11 0.5 m 17 1pc C 1 m B 10 kN
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
QUESTION 2 A steel cantilever beam is made of two structural tee- section beams welded together as shown in the Figure 2 below. Determine the allowable safe load (P) that the beam can carry. The allowable stresses are: 0-150MPa in tension and compression, T=100MPa in shear, and q=2000N/mm on the welded joint. 150 -200mm- -150- 25 weld 25 ΝΑ 25 M=P V=P -1.0m- Figure 2 weld 0.5m 31
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
Q1/ A thin-walled cantilever has a constant cross-section of uniform thickness with the dimensions shown in Figure. It is subjected to a system of point loads acting in the planes of the walls of the section in the directions shown. Calculate the direct stresses according to the basic theory of bending at the points 1,2 and 3 of the cross-section at the built-in end along the beam. 50N 2 mm 50 N 80N 2 mm 100 mm 2 36 mm 80 mm 24 mm