If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of this system is 0.5.Select one:O TrueO FalseStress concentration factor is defined as the ratio of the lowest stress or nominal stress in the component to the highest stress any where in the same component.Select one:O TrueO FalseA radial ball bearing fitted on to the shaft of a refinery vessel is subjected to axial load of 3340.8 N, take the service factor(K;) as 1.5. The equivalent dynamic load acting on the bearing will be .O 10022.40O 1670,40O 2505.60O 5011.20The outer diameter of muff is calculated as 81.2 mm. The shaft diameter of muff coupling is . mm.O a. 39.60O b. 34.10O c.61.38O d. 26.80

Answered: If a pinion having 20 teeth transmit…

Engineering

Mechanical Engineering

If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of this system is 0.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion with 15 teeth. The overall ratio of the gearbox is 6:1 and the gearbox is transmitting a power of 6000W. If the factor of safetv is to be reduced to an absolute minimum acceptable value and the gears are to be made from a material with a Yield stress of 540 MPa, what is the face width of the gears (in mm) Express your answer in the form 21.00 ie with two decimal place an no units
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; ku
A pair of straight teeth spur gear is to transmit 20kw when the pinion at 300rpm.the velocity ratio is 1:3.the allowable static stresses for the pinion and the gear material are 12MPa and 100MPa respectively.the service factor is 1.the pinion has 15 teeth and it's face width is 14 times the module.from the standpoint of strength only and taking into consideration the effect of the dynamic loading Determine; (A) module (B) face width (C) pitch circle diameter for pinion (D) pitch circle diameter for gear Tooth form factor;y=0.153_0.912÷no.of teeth Velocity factor;Cv= 3÷3+v
Please answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The driving sprocket runs at 225 rpm with a center distance of approximately 500 fpm. The transmission efficiency between the engine and the driving sprocket is 85%. 1.1 Determine the pitch and width of chain to be used. 1.2 Determine the number of teeth in each sprocket and the pitch diameters.
The module and the number of teeth on the pinion of a spur gear are 12mm and 15teeth respectively.A power of 400kW is to be transmitted at 1700rpm of width.if the involute teeth are of standard proportions (addendum=m) with the pressure angle of 22.5° determine (A) torque due to power delivered (B) tangential load (C) teeth width (E)load on the bearings
What is the fatigue-strength reduction factor for a shaft with an annealed sled-runner keyway under torsion if the notch sensitivity factor is 0.72?
A 21-tooth pinion rotating at 1000 rpmrpm meshes with a 33-tooth gear in a spur-gear reducer. Both pinion and gear are manufactured to a quality level of 9. A reliability of 0.9 has been specified and the transmitted tangential load is 2500 lblb. Conditions are such that Cm= 1.7. It is proposed that standard 25∘∘, full-depth teeth be used, with both pinion and gear hobbed from an AISI 4140 nitrided steel. The diametral pitch is 6, and the face width 2.000 inin. Suppose that the life of the pinion will be less than that of the gear, the lubricant bulk temperature does not exceed 250∘F∘F, both driver and driven devices are smooth-running, the gearset is external, gears made by conventional methods. Use the average value for the uncorrected surface-fatigue strength when choosing it from the appropriate table. Assume that the reducer is used for critical service applications. a)What is the dynamic factor (Cv) for the pinion? b)What is the AGMA Surface-Geometry Factor(I) for the pinion/gear…