If an optical fibre has an attenuation of 3 dB/km, then the light power after one kilometre would be approximately: Select one: O a. 50% O b. 25% O. 3% If the power in an optical fibre were reduced by 50% per kilometre, the attenuation fraction applicable for 10km of fibre would be: Select one: 10 Oa. 1 Ob. 1 O C.

If an optical fibre has an attenuation of 3 dB/km, then the light power after one kilometre would be approximately: Select one: O a. 50% O b. 25% O. 3% If the power in an optical fibre were reduced by 50% per kilometre, the attenuation fraction applicable for 10km of fibre would be: Select one: 10 Oa. 1 Ob. 1 O C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the ratio of the inner conductor circumference to the outer conductor circumference of a coaxial cable is 0.4993, what is the capacitance per unit length of the air-insulated coaxial line, in pF/m?
A 132 kV line with 1.253 cm dia. conductors is built so that corona takes placebif the line voltage exceeds 200 kV (rm.s.). If the value of potential gradient at which ionisation occurs can be taken as 30 kV per cm, find the spacing between the conductors.
A cellular radio transmitter has a power output of 3 W at 800 MHz. It uses an antenna with a gain of 3 dBi. The receiver is 5 km away, with antenna gain of 12 dBi. Ignoring feedline losses and mismatch, calculate (a) the EIRP in dBW (b) the free space path loss, (c) the power delivered to the receiver in W and dBm
In the microwave system given in the figure Find the attenuation between the input and the charge. Vi=9 volt, f= 10 MHz, γ=6+ j0,3, R= 47 ohm, c= 0,1 nF lesson: communication systems
An aluminum transmission line is to be replaced by copper having the same total resistance. If thecross-sectional area of the aluminum wire is 820 MCM, what would be the cross-sectional area of thecopper wire ? Given : Resistivity of aluminum = 17 Ω-CM per ft,Resistivity of copper = 10.37 Ω-CM per ft ( ANS ≈ 500 ??? )
A communication system uses 20 km of fiber that has a –3.1 dB/km loss characteristic.Find the output power (express it in both milliwatts and dBm) if the input power is200mW.
Please dont copy from other sources What is the role of Radio frequency in wireless power transfer?Provide a proper block diagram of ultrasonic wireless power transfer for better understanding
What is the total output power of a communication system with 2 watts ofpower if it passes a transmission cable with 2dB/km attenuation at 16 km?
In free space ⃗?⃗ (?, ?) = 70cos⁡(?? − ??)⃗?⃗ (V/m). Find the average power crossing a circular area of radius 2 meters in a plane ? = 0.
A radiograph was produced using 70kVp, 40mAs at 72 inches. How much time is needed to produce the same density at 40 inches if you are using the 200mA station?
Calculate the wavelength for an electron in the first orbit in the hydrogen atom, and the wavelength for an electron having a velocity of 1200km/s then compare the results
A BTS sending information at 1800 MHz with a 10 Watt (W) output power will only cover half the area of a comparable BTS transmitting at 900 MHz due to frequency. Explain how the 1800 MHz BTS might be used to cover the same region as the 900 MHz BTS and the tradeoffs involved.