If P = 28 Ib, choose the magnitude (Ib) and type (tension or compression) of the force in member DH. NOTE: Always choose two (2) answers but if the member is a zero-force member, choose one (1) answer only. - 3 ft →-3 ft →- 3 ft→ A B C 2 ft 4 ft H. 6 ft E G Select the correct response(s): O 29.70 O 42 O 22.14 O Compression Type here to search O 29°C Rain sh 近

If P = 28 Ib, choose the magnitude (Ib) and type (tension or compression) of the force in member DH. NOTE: Always choose two (2) answers but if the member is a zero-force member, choose one (1) answer only. - 3 ft →-3 ft →- 3 ft→ A B C 2 ft 4 ft H. 6 ft E G Select the correct response(s): O 29.70 O 42 O 22.14 O Compression Type here to search O 29°C Rain sh 近

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRUCTURAL 1. compute reaction A 2. determine the force carried by member BC due to 50kN applied load determine the force carried by member AC due to 50kN applied load 3. compute the horizontal deflection at B 4. compute the vertical deflection at B
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 19 cm as width, 20 cm as depth, and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
Determine the following : 1. Vertical reaction of hinge at A in pounds, Av 2. Horizontal reaction of hinge at A(lbs), Ah 3.Maximum shear value(lbs) 4. Maximum moment value (lb-ft)
The pillar is a cylinder that has a diameter of 68 mm , modulus of elasticity of E = 200 GPa . It is is fixed at A and B. The support at A is concrete and therefore rigid. The support at B can be considered rigid only if the reaction force at B does not exceed 110 kN . The lengths are LAB = 6.4 m and LAC = 3 m . 1)What is the maximum load, P, that can be applied such that the reaction at B does not exceed 110 kN ? 2)What is the reaction force at support A?
Calculate the maximum positive moment in beam BC in kN.m.0 Calculate the area of tension reinforcement As2 in mm2 necessary to balance the compression in the compression reinforcement.0 Calculate the moment M2 in kN.m provided by the compression reinforcement.0 really need answer please thank you
Set P1 = 70 kN, P2 = 50 kN. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member CG of the truss. b) Determine the force in member DE of the truss. c) Determine the force in member DF of the truss. d) Determine the force in member EF of the truss. e) Determine the force in member FG of the truss.
Which of the following is the nearest value for the force at member CD? a. 4 kN compression b. 6 kN tension c. 6 kN compression d. 4 kN tension
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
1) Calculate the effective depth of the section in PART B in mm.0 2) Calculate the depth of compression block of the section in PART B in mm. 3) Calculate the depth of the neutral axis of the section in PART B in mm. 4) Calculate the stress in the steel of the section in PART B in MPa. 5) Calculate the ultimate moment capacity of the section in PART B in kN.m.
For the beam shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 21 kN (↑); HA = 6.50 kN (←); VB = 21 kN (↑); HB = 6.50 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
2.) Given the truss shown, determine the value of the horizontal reaction at B. C= 14 KN D=20 KN E = 54 KN F = 61 KN g= 7 m The answer must be in KN.
The frame is used to support a live load of 1.575 kPa. Thickness of concrete slab is 124.903mm. Weight of concrete is 23.293 kN/m^3. Weight of beam BG,AH,CF,DE is 4.526 kN/m and that of is 5.413 kN/m L=5.918m Width"B" = 1.582m Compute the reaction at point A (kN) at member AD Answer: 71.118 Need solution