I ReviewIf the cable can sustain a maximum tension of 1.5 kN and the maximum sag is 3 m, determine the maximumdistance L between the supports.The 10 kg/m cable is suspended between theExpress your answer using three significant figures and include the appropriate units.supports A and B(Figure 1)• View Available Hint(s)Figure< 1 of 1μΑ?L = 8.68mL.SubmitPrevious Answers Request Answer3 mB

If the cable can sustain a maximum tension of 1.5 kN and the maximum sag is 3 m, determine the maximum distance L between the supports. The 10 kg/m cable is suspended between the supports A and B (Figure 1) Express your answer using three significant figures and include the appropriate units. > View Available Hint(s) Figure 1 of 1 HA L = 8.68 m Submit Previous Answers Request Answer 3 m

If the cable can sustain a maximum tension of 1.5 kN and the maximum sag is 3 m, determine the maximum distance L between the supports. The 10 kg/m cable is suspended between the supports A and B (Figure 1) Express your answer using three significant figures and include the appropriate units. > View Available Hint(s) Figure 1 of 1 HA L = 8.68 m Submit Previous Answers Request Answer 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
You open a restaurantand hope to entice customers byhanging out a sign (Fig. ).The uniform horizontal beam supportingthe sign is 1.50 m long, hasa mass of 16.0 kg, and is hingedto the wall. The sign itself is uniformwith a mass of 28.0 kg andoverall length of 1.20 m. The twowires supporting the sign are each32.0 cm long, are 90.0 cm apart,and are equally spaced from themiddle of the sign. The cable supportingthe beam is 2.00 m long.(a) What minimum tension mustyour cable be able to support without having your sign come crashingdown? (b) What minimum vertical force must the hinge be able to supportwithout pulling out of the wall?
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
A cable is tied to a car, which then speeds away. The car and the object to which the cable is tied are considered rigid. The car weighs 3000 lbs. The cable is 100 ft long and has an area of 0.2 in2. If the car is going 5 mph when it reaches the end of the cable, calculate (i) deflectionin the cable, (ii) Stress in the cable, (iii) Max. force in the cable. (Ecable = 12 × 106 psi)
If Poisson's ratio of a material is 0.5, then the elastic modulus for the material is a)three times its shear modulus b)four times its shear modulus c)equal to its shear modulus d)indeterminate
Answer no. 17. Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
Elasticity and Stress Analysis: Torsion The three cell box girder of Figure 1 Q.1 is subjected to a clockwise torque of 10,000 kNm.Sketch the shear flow diagram for the girder.Hence, determine the shear stress set up in each member and the angle of twist of thegirder.Given: Modulus of Rigidity = 80 GN/m2 Equations: T=2Ah 2G(theta)A=(tau)L q1=q2+q3
please very urgent The bank in the figure is thought that a person is sittingthe force exerted on the board as 300 NIt is given. Elasticity of the boards that make up the benchmodule E = 7 GPa, the width of a board is 150 mm andSince the height is 30 mm, the person sitsCalculate the slump at the point. (Hint: ABas if built-in board A and BThink about it.) Dimensions ar in mm.
If the displacement is doubled, the elastic potential energy of the system will
A 540-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 140-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.) (a) Find the (magnitude of the) tension T in the cable.N(b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component _____N vertical component _____N
On a forest trail a 4m long birch tree trunk is laid across a ravine as a bridge. The trunk is 4m long and just touching each side of the ravine. The trunk is 20cm in diameter and roughly cylindrical. The Young's modulus of birch is 15.2 GPa and its density is 610kg/m3610kg/m3. How far does the middle of the trunk bend under its own weight? (answer in mm)