If the coefficient of static friction between the crate and the inclined surface is a) Draw the FBD b) Determine the maximum angle O before sliding happens. (Assume tipping over does not happen first)

If the coefficient of static friction between the crate and the inclined surface is a) Draw the FBD b) Determine the maximum angle O before sliding happens. (Assume tipping over does not happen first)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Related questions

Q: A plant is 10m ong is placed on a horizonta positin wth ts two ends resting on to inclined planed.…

A: 1. Value of x when plank will start to the side is 5.8655 m. 2. If P=100 kN the reaction of A is…

Q: i the coefficient of static friction at B is µ,=0.4, determine the largest angle 0 and the minimum…

Q: QI-The W=250o-N block shown in Fig. below is in contact with 30° incline. The coefficient of static…

A: Given W=2500 N μs=0.25 P=? θ=30o

Q: Part A The crate shown in (Figure 1) has a mass of 105 Kg and center of mass at G. If the…

A: GivenM=105kgμs=0.20

Q: Q1-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

A: Given data Mass of man = 75kg Mass of box = 145 kg. Coefficient of static friction between box and…

Q: forces on each block. The coefficient of friction under each block is 0.35 and angle alpha is 33…

A: Solution :- Given data :- μ =0.35α =33ο

Q: A small block of weight W is placed on a plane inclined at an angle θ to the horizontal The…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Find the least value of P that will just start the system of blocks as shown in the figure moving to…

Q: Q2: The ladder in fig.(1), has a uniform * weight of 100N and rests against the wall at B.If the…

Q: Determine the angle of contact () in degrees of the belt supported on a pulley if the belt is having…

Q: A block with mass (3 kg) is pl a) What coefficient of friction b) If the coefficient of friction i…

Q: If a block is stationary, the friction will always be f = µN, whereu is the coefficient of static…

A: Case - 1: When the block is stationary and no external force is acting on a block, then the friction…

Q: 6.7 Compute the horizontal force P required to cause motion to impend up the plane for the 100-lb…

A: Given Mass, m = 100 lb = 45.35 kg Coefficient…

Q: The drum has a weight of 100 lb and rests on the floor for wich the coefficient of static friction…

Q: 1. What is the maximum mass that block A can carry that will not cause block B to slip. The…

Q: Determine the range of weight (W) that the block shown in figure (3) may have, which will make it…

A: For solution refer below images.

Q: Block A The coefficie of static friction between qnd the ra woighs 55 05 block B 20 lb. 30

A: givenblock A weights W1=55lbblock B weights W2=20lbpulley is light and smooth static friction…

Q: Q2/ Arm ABC acts as a brake on the wheel as shown in Fig. 2. The coefficient of static friction at B…

Q: What is the maximum mass that block A can carry that will not cause block B to slip. The contacting…

Q: Compute the total reaction at the axle of the compound cylinder having a weight of 120N and radius…

A: Suppose α is the angular acceleration of pulley a1 is the acceleration of weight…

Q: i. To prevent motion downward (keeping the block stationary on the incline); ii. To cause motion…

A: To determine the value of F for the given conditions. Given: W=50 N

Q: 1.) Compute the weight of block B that will prevent the two block system from sliding. Block A…

Q: Q1- In the arrangement shown in Fig what is the minimum coefficient of friction to prevent the 8.0kg…

Q: A lightweight rope is wrapped around a drum as shown in Fig. drum and the ground is 0.30. Determine…

A: Draw the free body diagram for the above system.

Q: The coefficient of friction is 0.10 and the pulleys are assumed to be frictionless. 40 kN 60 kN N…

A: To find weight W

Q: 30° 5. A box weighs 150 kg. The coefficient of static friction between the box and the ground is…

A: To check: Whether the man can pull the box without slipping. Given: The mass of box is mb=150 kg.…

Q: Pls answer asap. Badly need it. Three identical blocks are placed on top of each other on a…

Q: Determine the range of weight (W) that the block shown in figure (3) may have, whi make it neither…

Q: 2. Determine the horizontal force P in the figure to start the 400 lb wedge (a) moving to the right…

Q: The static coefficient of friction is smaller than the kinetic coefficient of friction. الاختيارات…

A: Ans) : False Because static coefficient of friction is greater than the kinetic coefficient of…

Q: Activity 1. In the figure shown, the coefficient of friction is 0.25 for all surfaces of contact.…

Q: In Fig. 3, determine the smallest vertical force P required to push the wedge between the two…

A: To find: The smallest vertical force P required to push the wedge between the two identical…

Q: DRAW F. B. D AND IOWTHE DIRECTION OF FRICTION FORCE

A: GIVEN:

Q: Q5: - Find distance S which the 90 kg person can climb without slip the 4 m ladder at lower end A.…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Determine the smallest force the man must exert on the rope in order to move the (136)kg crate shown…

Q: the coefficient of static friction at B is p,-0.4, determine the largest angle and the minimum…

Q: 1. A car is parked on an incline. The car has weight W centered at G. For full credit, you must draw…

A: FBD of car, RA = RB = (W/2) cos(θ) For slipping, Take sum of forces in X direction =0, -W sin(θ) +…

Q: l'he uniform pole of length I and against the supporting surfaces she cient of static friction is u,…

A: given:static friction μs=0.25length of the pole=lmass of the pole=m

Q: The frictional coefficient has a value of 0.26795, and the normal force is 20kN. Determine the angle…

Q: How much force F must be applied to a wedge A (negligible weight) to move the 500 kg block up the…

Q: Determine the magnitude of the block W to cause the counterweight of 100 kg to slide up. Coefficient…

Q: Ql- In the arrangement shown in Fig ,what is the minimum coefficient of friction to prevent the…

Q: 4. The coefficient of friction is 0.200 between the rope and drum and at all surfaces. Calculate the…

Q: The truck has a masS oad it can pull if: a) the truck has rear-wheel drive while the front wheels…

A: To given thatThe truck has a mass, m=1.25kgCoefficient of friction between wheel and ground…

Q: Determine the smallest force the man must exert on the rope in order to move the (162 kg crate shown…

Q: Q1- In the arrangement shown in Fig ,what is the minimum coefficient of friction to prevent the…

A: g=9.8ms2 T2=mg=4×9.8T2=39.2 NT1cos30o=T2T1=39.8×2T3T1=45.26 NT1sin30o=T3T3=45.26×12T3=22.63 N

Q: A 40 kg block is resting on an inclined plane making an angle of 20° from the horizontal. If the…

A: GIVEN DATA- MASS OF BLOCK m=40kg FRCITION COEFFICIENT =0.60 WE HAVE TO FIND FORCE APPLIED

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

If the coefficient of static friction between the crate and the inclined surface is
a) Draw the FBD
b) Determine the maximum angle O before sliding happens.
(Assume tipping over does not happen first)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Assume that block Q do not slip on block P. You can take the static coefficient of friction between Q and P as ?. Furthermore, it is to be noted the friction offer by the surface R is zero. You are also requested to draw the FBD.
The block of weight W = 10 kN is pulled by the force P inclined at the angle = 15 to the horizontal. Find the smallest force P (in kN, round-off to 2 decimal places) that would cause impending sliding of the block. The angle of static friction between the block and the ground is = 15.
A. Determine the angle between the wedge and the concrete and the wedge and the floor. B. Calculate the coefficient of static friction between the concrete and floor.
One end of a uniform meter stick is placed against a vertical wall. The other end is held by a lightweight cord that makes an angle ? with the stick. The coefficient of static friction between the end of the meter stick and the wall is us =0.40. B. A block of the same weight as the meter stick is suspended from the stick, as shown, at a distance x from the wall. Assume that angle ? = 15° in this problem. What is the minimum value of x for which the stick will remain in equilibrium? C. When angle ? = 15°, how large must the coefficient of static friction be so that the block can be attached 0.10 m from the left end of the stick without causing it to slip?
The pickup truck pulls the wooden crate, as shown in Figure 2. The truck has a mass of 1.25 Mg and a center of mass at G. The coefficient of static friction between the truck's wheel and the ground is µ = 0.5, and between the wooden crate and the ground is µs' = 0.4. Determine the greatest weight of the wooden crate the pickup truck can pull if: a) the truck has rear-wheel drive while the front wheels are free to roll, and b) the truck has four-wheel drive.