If the connection is bolted connection, find the maximum load that can carried by the connection if the type of bolts is A325 threaded in the plane of shear. The bolt diameter is 5/8" and the thickness of gusset plate is 3/4". PL10x3/4 11.5| 3 | Pu =-4 '10 t'i lint OO 00 1.5 A36 Steel 2MC12X31 Section a-a

If the connection is bolted connection, find the maximum load that can carried by the connection if the type of bolts is A325 threaded in the plane of shear. The bolt diameter is 5/8" and the thickness of gusset plate is 3/4". PL10x3/4 11.5| 3 | Pu =-4 '10 t'i lint OO 00 1.5 A36 Steel 2MC12X31 Section a-a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection consists of two 3/8" plates fastened to each side of one 13/16" plate.Assume 7/8" diameter bolts and standard punched holes. Use A36 steel. The plate is 13” wide. Note: Be sure to check all failure modes; bolt failure modes, and member failure modes(including block shear)
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
Given W 16x36 section as shown below (Fy = 50ksi, Fu= 65ksi). The holes are 3/4 inch in diameter. The connection is bolted at the web only. Assume x=0.76 inch, determine... 3. The Tensile strength Tn (LRFD) neglecting block shear failure mode.
Q1) A bracket must support the service loads applied at angle given in table below, which act through the center of gravity of the connection. The connection to the column flange is with 4 bolts of diameter given in table, bolts type is A325X. A992 steel is used for all components. Find the value of DL and Live load which make the connection safe , if you know that DL = 3 live load Note : angle , bolts diameter according to your last ID number . Last ID number Load’s angle Bolts Diameter 0 20 12 1 25 14 2 30 16 3 35 18 4 40 20 5 45 22 6 47 24 7 50 26 8 53 28 9 55 30
Plz, solve this problem as detail as you can? Steel Structure Design a concentrically loaded bolted connection with the following given information. Also verify your design and draw s sketch showing final layout of the connection. Size and type of bolts: 3/4-in A325 (Group A) bolts in standard-size holes with threads excluded from the shear plane in a bearing-type connection shown in figure 1. Use Fu= 58 ksi and assume edge distances to be 2 in and the distance center-to-center of holes to be 3 in, Assume that deformation at bolt holes is a design consideration. Pu = 345 k using LRFD
Please answer it asap for an upvote. Thankyou. An A992 steel plate (12mm thick, in yellow) is connected to another A992 steel plate (12mm thick, in gray) using four bolts having a diameter of 33mm. If "x" makes the net width along bolts 1-2-4 equal to that of the net width along bolts 1-2-3-4; Compute the design tensile fracture capacity using the most critical net area (in kN).
Determine the net area An of a 1/4 in by 4 inches plate and the diameter of the bolt is 7/8 in. Assume plate thickness is 1/4 in.
Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use Fult=65 ksi? 2-Why we consider Wt section? this procedure as I understand is applied when the connection is to flange. 3-The net area estimated is only for one bolt, i believe An=11.80-(4*7/8*0.305)=10.733 inch^2. 4-x bar which I consider is from case 2 only since case 7 will not work, x bar is only Tw/2 value?. U value=1-(0.1525/6.50)=0.977. Could you please advise? Thanks.
Determine the design strength Puand the allowable strength Pa for the connection shown if 7/8 in A325 bolts (threads excluded) are used in a slip-critical connection with a factor for fillers,hf = 1.0. Assume A36 steel and Class B faying surface and standard size holes
Compute the capacity of the connection considering all possible modes of failure. Assume that the determination @ bolt is a design consideration, A490 bolt are used with threads included from shear planes.
How many bolts are required (LRFD and ASD) for the bearing-type connection shown if PD = 120 k and PL = 150 k? A325 7/8 -in bolts, threads excluded from shear planes.
A 14x1/2 inch steel plate is used as a tension member. The end connection to the gusset plate is by six 7/8-inch-diameter bolts, arranged with staggered pitches of 2 inches and gage distances of 2-1/2 inches as shown. (a) What is the net area for path A-F-J? (b) What is the net area for path B-E-H-K? (c) What is the net area for path C-D-G-I-L? (d) What is the effective net area for the plate shown?