If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter of the tank is 20m then is the tank filling or emptying? At what rate is the water level rising or falling in the tank?

If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter of the tank is 20m then is the tank filling or emptying? At what rate is the water level rising or falling in the tank?

Name: Provide handwritten solution asap !! Don't copy If the inlet diameter
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Provide handwritten solution asap !! Don't copy If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and thediameter of the tank is 20m then is the tank filling or emptying? At what rate is the waterlevel rising or fallin

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discuss which dimensionless pump performance parameter is typically used as the independent parameter. Repeat for turbines instead of pumps. Explain.
A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Gardeners are holding a nozzle at the end of a hose to wash way mud from landscaping. The nozzle exit has a diameter of 10cm and the water is flowing at a rate of 12 m3/min. In this situation, what is the average water exit velocity and what is the horizontal resistance force required to hold the nozzle? Any help would be great
Roman aqueduct customersobtained extra water by attaching a diffuser to theirpipe exits. Fig. shows a simulation: a smooth inletpipe, with or without a 15° conical diffuser expanding to a5-cm-diameter exit. The pipe entrance is sharp-edged. Calculatethe fl ow rate (a) without and (b) with the diffuser.
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
A Pelton turbines is desired to be installed. clear as it is believed to be necessary It can calculate the hydraulic power of turbines with a head of 210 meters relative to each other. Features: do = 120 mmku = 0,42kco = 0,96w2 = 0,85 (C1 – U1)β2 = 160 °
When a jet of water gushing from a short pipe with a diameter of D= 5 cm, located at a depth of h= 6.6 m from the surface of a fixed level reservoir shown in the figure, hits a horizontal plate that makes an angle of 30o with the jet axis (friction effects are neglected), a)Determine the scalar value and direction of the impact force exerted by the water on the plate (Enter the numerical value of the direction you think is correct in the direction-number image in Figure 3 in the box named "Direction-effect". For example: '1' will be entered for the upward direction). b)Determine the scalar value of the reaction force of the plate and determine its direction (Enter the numerical value of the direction you think is correct in the direction-number image given in Figure 3 in the box named "Direction-reaction". For example: '1' will be entered for the upward direction).
The diameter of the ball is 30 cm as shown in the figure. Calculate the river current velocity [m/s]. (NOTE: Neglect the weight of the cable. SGBALL = 0,20 PWATER = 1000 KG/M3 CD,BALL=0,12
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N