Answered: If the maximum force that any member…

If the maximum force that any member can support IS 4 kN in tension and 3 kN in compression, determine the maximum force P that can be supported at point B. Take d = 1m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: The graph shows the displacement-time history for the rectilinear motion of a particle during an…

Q: At 68 ˚F water has a dynamic viscosity of about 2.11 x 10 -5lb-s / ft2, solve the kinematic…

A: Kinematic viscosity = dynamic viscosity/ density of fluid. Given : dynamic viscosity = 2.11 x 10 -5…

Q: A soil has an effective unit weight of 11.33 kN/m3, void rato of 0.62 and water content of 16%.…

A: Void ratio (e)=0.62 Water content (w)=16% To find bulk density of soil

Q: A projectile is fired vertically with an initial velocity of 122 m/s. Calculate the maximum altitude…

Q: A wastewater treatment plant is being designed for a small, growing community. Average flow to a…

Q: Study the water tank illustrated in Figure 1 below and calculate the horizontal distance (x) the…

A: To find out the horizontal distance of free jet of water travel before striking the ground.

Q: As future engineers, how can you apply the sustainable development in your profession?

A: A guiding concept in sustainable development is maintaining the ability of nature's processes to…

Q: A hydraulic jump occurs in a triangular (V-shaped) channel with side slopes 1:1 (vertical to…

A: GIVEN- Hydraulic jump occurs in a triangular (V-shaped) channel. Side slopes of channel is 1:1…

Q: In traveling a distance of 2.3 km between points A and D, a car is driven at 91 km/h from A to B for…

Q: A wall is 2.5 m high and 6m long consists of 200 mm clay bricks with 50mm x 100mm plastered wood…

A: Giventhat Wall is 2.5m high Length= 6m Consists 200mm clay bricks and 50×100 plastered wood studs…

Q: A 1m wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is…

Q: 3.6 m y A2 = 1,384 mm^2 A3 = 536 mm^3 F A (1) 2.4 m Rigid bar B (2) E 1.8 m (3) D X 3.0 m The…

A: Objective: To determine the vertical displacement of joint D. Given: Modulus of elasticity for the…

Q: How would knowledge of metallurgy benefit an engineer?

A: The branch of materials science and engineering known as metallurgy is responsible for researching…

Q: Using Method 1, what is the basic wind pressure, q, at the upper part of a 40 ft high hospital in…

A: To solve this problem, firstly the value of wind speed need to be considered from national weather…

Q: A concrete sidewalk is constructed between two buildings on a day when the temperature is 25 C. The…

A: Given : Length of sidewalk = 6m Temperature = 25 degree C Length of slab = 3m Temperature increase…

Q: Soil is a mixture of air, solid particles, water, or other fluids, as shown in this figure. Soil…

A: Objective: To determine: (a) water content and unit weight of the moist soil (b) void ratio and…

Q: A heat pump maintains a dwelling at 68°F. When operating steadily, the power input to the heat pump…

Q: 1.08) for speeds v € (90,110) kph? Values for side friction f may be interpolated using Table 2. r:…

A: Superelevation is the transverse slope provided to counteract the effect of centrifugal force and…

Q: Determine the maximum stress of the plate. • rivet hole diameter= 2 cm • width of the plate= 7 cm…

Q: 4. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Given : b = 250 mm, d = 460 mm fy = 276.5 MPa fc' = 20.7 MPa Required: Ultimate moment…

Q: Calculate uniform load beam reactions, normal forces, shear forces and bending moment. Also draw…

A: Given data in question UDL = 2kN/m Point load 1.414 kN Angle 45° Span length 3 m To find out…

Q: What is the design wind pressure on a windward wall 30 feet above the ground for a building with…

A: q=17.3 psfG=0.85Cp=0.8I=1.0To determine:Design wind pressure

Q: The degree of kinematic indeterminacy of the rigid frame with clamped ends at A and D shown in the…

Q: Current Attempt in Progress X Incorrect Calculate the moment (positive if counterclockwise, negative…

A: The moment at centre of bolt= ((250sin 32)(30)) - ((250cos 32)(215)) = -41608.19 N-mm = -41.61 N-m…

Q: On grid paper draw a scale top view 2D diagram of the floor plan of a living space. It must include…

A: To make a 2D diagram of a floor plan we use the following steps:- take a corner-to-corner…

Q: An industry produces a degradable waste at flow rate of 0.72 m³/day. Concentration of pollutant in…

A: According to given time An industry produces a degradable waste at flow rate of 0.72 m³/day.…

Q: The beam is used to support a dead load of C kN/m, a live load of A kN/m and a concentrated live…

Q: Design the number of 36 mm diameter bars to support the maximum positive moment of Mu=1600 kN.m. Use…

Q: Road system is an essential network for transporting goods and commuters from one place to another.…

Q: Problem 2 Determine the forces in the members AB, AC, and AD of the space truss shown in figure…

A: Given : Determine forces in member AB, AC and AD?

Q: At time t = 15 s, the velocity of a particle moving in the x-y plane is v=0.12i + 2.15j m/s. By time…

A: The given data is shown below: t=15 sv=0.12i+2.15j m/st=15.14 sv=0.01i+1.98j m/s

Q: . Determine . Determine .. Determine the minimum the maximum (or negative) reaction at B. positive…

Q: A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid…

A: Given data in question Pressure = 15 and 30 atm Volumes = 1.2300 and 1.2310 L To find out Bulk…

Q: A cantilever beam of negligible mass has a mass m at its free end. If the length of the cantilever…

A: GIVEN- A cantilever beam of negligible mass has a mass m at its free end. DETERMINE- If the length…

Q: 2. The following values were determined in a series of tape measurements of a line: 920.58, 920.40,…

Q: Show mathematically, Relationships 1-6 are true 1.)Single Payment 2.)Uniform Series 3.)Compound…

Q: Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of…

Q: A GPS enabled device has many uses. Write or record a short description of what GPS stands for, how…

A: Reference : Surveying/ Mapping and Photogrammetry, GPS To determine : 1. Small Description 2.…

Q: . Problem 1- Classify the soil to be used as a highway subgrade material using AASHTO classification…

A: To determine the soil classification as per AASHTO.

Q: 4. Determine the vertical deflection of joint C of the truss shown. In addition to the load at joint…

A: Given data in question Load 14 kips Area 4 inch2 Lengths of each member Modulus of Elasticity…

Q: 2. Determine the Magnitude and type of the bar forces in the members indicated below. E Member BC BD…

A: Find the length and angles of the members using geometry. Apply equilibrium of forces at each joints…

Q: 2.3.2 WP The deepest known spot in the oceans is the Challenger Deep in the Mariana Trench of the…

A: Finding pressure at depth

Q: The average speed of vehicles on a road with a downgrade of 4% is 90 kph. A traffic study was…

A: Given:Design speedV=90 kphGradientn=-4%Current braking distanced=120 mReduction in braking…

Q: CE 2131 PRACTICE PROBLEM ON CLOSED TRAVERSE. Determine the adjusted bearings of the following…

Q: 30 ft- 6 klf

Q: Two reservoirs are connected by two pipes P and Q. The pipes have the same diameter and length and…

A: Given data: Two reservoirs are connected in parallel by two pipes P and Q. Friction factor of P is 9…

Q: Eij A body is subject to the following strain distribution. x² + 2yx 3 + 10zx +10xy 3+10zx 5y + z2x…

A: Given data:- ∈ij=x2+2yx3+10zxz3+10xy3+10zx5y+z2xx2+2yz2z3+10xyx2+2yz2x2+y2×10-2

Q: A 6 ft 250 lb/ft 6 ft B 8 ft 60 120 lb/ft с

A: We have find support reaction in this figure.

Q: For the beam below, (a) draw the shear and moment diagrams and (b) determine the maximum normal…

Q: Determine the maximum stress of the plate.

A: Given, Determine the maximum stress of the plate. Rivet hole diameter.d= 2 cm Width,b= 6 cm…

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

If the maximum force that any member can support IS 4 kN in tension and 3
kN in compression, determine the maximum force P that can be supported
at point B. Take d = 1m.
E
B
d/2d/2
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the design angle θ (0° ≤ θ ≤ 90°) forstrut AB so that the 400-lb horizontal force has a componentof 500 lb directed from A towards C. What is the componentof force acting along member AB? Take Φ = 40°.
Calculate the forces in members AB, BG, and GF using the method of section.
Determine the normal force, shear force, and moment at point C. Take M = 18 kip.ft
Given beam (P = 24 kN)a) Find the internal forces at the midpoint of the BC length by cutting method.b) Draw the N, T, M diagram.
If FA = 7 kN and FB = 5 kN, represent the force system acting on the corbels by a resultant force, and specify its location on the x–y plane.
A truss is loaded with nodal force at C as shown TOS-003. If the truss members have identical rectangular section of 5 cm x 8 cm, with E = 70 GPa, compute the vertical displacement at joint C .
Solve for axial forces at BC, BG and GH using method of section
Assuming that E=200 GPa and I=2.63x108 mm4, determine the total force P exerted by the 25 mm diameter, 2m long steel rod at B.
(a) Compute the vertical displacement of the hinge at C in Figure P8.34. EI is constant for all members, E = 200 GPa, I = 1800 × 106 mm4 . (b) The designer would like to offset the vertical displacement of the hinge at C by moving the support A. How far should support A be moved horizontally?
The vertical load of 115 kN and horizontal load 125 kN are applied at joint F and B by using method of sections determine the force in member EG, DG and DF.
Compute the vertical components of the hinge forces at C as they act upon member AC in kN P= 89 kN and x= 3.7 m. Write numerical value only and in 2 decimal places
Referring to the figure, determine the force in member DF using method of sections