On grid paper draw a scale top view 2D diagram of the floor plan of a living space. It must include 2 exterior doors, 2 rooms, and  four windows

Q: Question 6 a) With regards to the relationship between the sight distance and the length curve as…

A:

Q: What will be the non-passing sight distance on a highway for a design speed of 100 kmph when its…

A: Given- Design speed V=100 kmph, gradient n=+2%=0.02, coefficient of friction f'=0.7, brake…

Q: IX. PROBLEM SET NO.1 1. A closed tank contains 0.610m of mercury (sp.gr. 13.6), 1.524m of…

A: Given data  Depth of oil (ho) = 2.438 m Depth of water (hw) = 1.524 m  Depth of mercury (hHg) =…

Q: A single-stage rocket is launched vertically from rest, and its thrust is programmed to give the…

A:

Q: 200 lb B 350 lb cars while the rain is slowing 90 km h May belon Test! S 25 Mg Fig. P12.12 20 Mg…

A: WA =200lb WB=350lb To find tension in cable and acceleration of each cable

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Given :- b = 250 mm d = 460 mm fy = 276.5 Mpa f'c = 20.7 Mpa  Required :- Maximum steel ratio, ρmax

Q: municipality treats 15x10^6 gal/day of groundwater containing the following: CO2 =17.6 mg/L, Ca2+ =…

A:

Q: 1.5 m Determine the forces in each member of the truss. 2m B 4 kN 3 kN 2m C

A: Given data in question  Load 4 and 3 kN Dimensions 2,2 and 1.5 m To find out  Member forces

Q: bigger toward the smaller end. What is the rate of increase in velocity at the entrance if the…

A: Given data Length= 100ft d1= 8ft d2= 2ft Velocity= 80ft/ s

Q: Solve Maximum deflection

A: To find maximum deflection

Q: 00 GPa and a (a) the maximum stress at Point A on the Cross-section a-a, (b) the vertical…

A: 0.8m solid bar0.5m solid leverE-200GPashear modulus=86GPaTo find:-a) maximum stress at point A on…

Q: Answer no.2 question but plss adjust Correction in soil c in prob1 its 35%  clay

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: Problem 1: From the following counts, which were taken on a major arterial during the evening peak…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Calculate the negative moment - Mc and Ma with the 3-moment equation!  answer-Mc = -20 k.Nm Ma = -29…

A: To determine:-Negative moments-Support reactions-Maximum moments-BMD

Q: 1. 3(3x² + y²) dx - 2xy dy = 0.

A: As per the rules we can answer only the first question and rest others can be reposted.

Q: Show mathematically, Relationships 1-6 are true 1.)Single Payment 2.)Uniform Series 3.)Compound…

A:

Q: How was 20degrees gotten ?

A: Objective: To follow the question and explain how the value of 20 degrees was came upon.   The given…

Q: For a catchment area of 12 hectares, the S-curve (or s-hydrograph) due to rainfall intensity of 1…

A:

Q: Q-A rectangular column section of 250mm x 400mm is reinforced with five M30. steel bars of grade Fe…

A: Given data- Rectangular column section- 250 mm×400 mm,5 steel bars, Fe500,dia d=20 mm,M30 concrete,…

Q: A rectangular beam shown is subjected to superimposed dead loads ((neglect the wt of beam) and…

A:

Q: . A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension nly with 3-25 mm bars.…

A: Given data  b=250mm d=460mm fs=?

Q: The culturable commanded area for a distributary is 2 x 108 m². The intensity of irrigation for a…

A:

Q: ) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of…

A:

Q: Problem 4.91 The couple moment acting on the pipe has a magnitude of 300 Nm. (Figure 1) Figure 1 of…

A: Given : M = 300 N-m TO Find : Determine the magnitude F of force applied to the wrenches ?

Q: A traffic surveying conducted on a road yield an average daily traffic count of 5000 vehicle. The…

A: Given- Daily traffic count TC=5000 vehicle,Design period n=15 years,Growth rate G=7.5%,LSF=1.3, It…

Q: The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of…

A: Given that : Diameter of hole = 44 mm G  = 77 GPa A) Angle of twist of end A with respect to end D…

Q: Problem A jet of water of diameter 10 cm strikes a flat plate normally with a velocity of 15 m/s.…

A: Given: Diameter of jet d=10 cm=0.1 m, Velocity of jet V=15 m/s, Velocity of the plate U=6 m/s,…

Q: Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm •…

A:

Q: Problem- For two infinite slopes (one in dry condition and other in submerged condition) in a sand…

A: Given: Angle of Shearing resistance ϕ=300, Factor of safety = 1.5, It is required to find the slope…

Q: 4. Determine the three components of force (F3) the three concurrent forces as shown in the figure.…

A: To find the X, Y and Z component of the force F3 Let X component of F3 be Fx Let Y component of F3…

Q: 4/39) Determine the forces in members BC and CF of the loaded truss, repeated here from Prob. 4/19.…

A:

Q: Using Method 1, what is the basic wind pressure, q, at the upper part of a 40 ft high hospital in…

A: To solve this problem, firstly the value of wind speed need to be considered from national weather…

Q: 3. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Answer  We are given Width of beam b = 250 mm Effective depth of beam d = 460 mm Area of steel As…

Q: A 3 ft diameter log with specific gravity of 0.82 divides two shallow ponds as shown in the figure.…

A:

Q: 1. An air dry (not oven dry) processed clay powder sample has the following measurements: - Mass of…

A:

Q: 3-57. If each cord can sustain a maximum tension of 50 N before it fails, determine the greatest…

A:

Q: Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of…

A:

Q: 3.13 3.14 In Problems 3.13 through 3.17, compute the corrected horizontal distance (assume normal…

A: 3.13) h = 6.35 feet            Lo = 198.61 feet  Cs (correction due to slope) = -h2/2Lo

Q: of point B.

A: Given: Weight of uniform beam is 120 Kg

Q: In a 5 m wide rectangular channel, the velocity u distribution in the vertical direction y is given…

A: GIVEN:Rectagular channel Width (b) =5m Velocity (u) =1.25y1/6 Flow depth= 2m   To determine:…

Q: Consider the frame shown in (Figure 1). Suppose that P = 400 N and M= 800 m. Find the reaction at C,…

A: Given : P = 400 N and M  800 N-m To Find : Reaction at C ?

Q: 3-10. The block has a weight of 20 lb and is being hoisted at uniform velocity. Determine the angle…

A: Given : Block weight = 20 lb Determine the angle thetha and the force in cord AB?

Q: A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the…

A: To find out the axial stress developed in the rod in MPa or N/mm².

Q: The velocity of a particle which moves along the s-axis is given by s = 50-6t2 m/s where t is in…

A:

Q: A circular duct is to measure 20.5 centimeters in diameter and 75 centimeterslong. It has a butt…

A: Given:- d=20.5cm l=75cm butt seam To find:- nearer hundreth centimeter

Q: The wind pressures used in the design of buildings in accordance with the International Building…

A:

Q: 7. In 1978 the magnetic bearing of a line OA was N15°45′W, the magnetic declination at that time is…

A: To determine the  a) Magnetic declination in 1998 b) Magnetic bearing in 1998 c) True bearing in…

Q: Draw the shear and bending moment diagram of the following beams Problem 1 A P W 5m P 8m 32kN 26kN/m…

A:

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given data  Find force in each member.  T = Tension = positive sign  C = Compression = negative…

Q: A cantilever beam of negligible mass has a mass m at its free end. If the length of the cantilever…

A:

Floor Plan Details

Floor plans are the scale drawings that show the interplay of rooms, spaces, and physical objects. They are an integral part of the house plan. They let you see how people will move around the room. Floor plans determine the suitability of space for its intended use, work through any potential issues, and redesign before moving on to more comprehensive planning or constructing phases. It shows the different alternatives and perspectives related to the location and dimension of rooms, windows, doors, kitchen and all other things as per the requirement by the user. Many consultants give their own floor plans as reference to the clients for a better idea and to develop good floor plans.