If the most efficient of all cross sections can be used, what shape and size of open channel would you recommend to carry 300 cfs with a velocity of 7 ft per second? Draw a representative figure for each part of your solution. For this problem, study the 4 possible cross sections and defend your final recommendation. Assume logical frictional/roughness parameters depending on the equation you choose to use. Your final output must be a construction drawing of your recommended cross section.

If the most efficient of all cross sections can be used, what shape and size of open channel would you recommend to carry 300 cfs with a velocity of 7 ft per second? Draw a representative figure for each part of your solution. For this problem, study the 4 possible cross sections and defend your final recommendation. Assume logical frictional/roughness parameters depending on the equation you choose to use. Your final output must be a construction drawing of your recommended cross section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the most efficient of all cross sections can be used, what shape and size of open channel would you recommend to carry 300 cfs with a velocity of 7 ft per second? Draw a representative figure for each part of your solution. For this problem, study the 4 possible cross sections and defend your final recommendation. Assume logical frictional/roughness parameters depending on the equation you choose to use. Your final output must be a construction drawing of your recommended cross section.
A rectangular planned timber flume is to carry 3.01 m3/s, with a velocity of 1.78 m/s, slope of flume is 0.000155. What should be the width of most efficient rectangular section to be used?1.84 m1.79 m1.50 m1.22 m
The horizontal bar shown (Length = 15.0 feet) rests on smooth inclines. Compute the distance x atwhich load T= 250 lbs should be placed from point B to keep the bar horizontal? show fbd and complete solution
An open channel to be made of concrete is to be designed to carry 3.6 cum/s at a slope of 0.00053. Assuming n = 0.044. Determine the diameter in m for the most efficient section for a semi-circular section. Round your answer to 3 decimal places.
What size average cast iron pipe should be used to deliver 0.0283 m3/s of water at 20°C through 1219mwith a drop in the hydraulic grade line of 21.3 m?
For rectangular reinforced concrete beam shown in fig. Find the spacing of Ø10 mm stirrups at the critical section if:1- Stirrups are vertical. 2- Stirrups are inclined by 45˚.Use??′??=28420???
A rectangular channel is to carries 1 m3/s. Determine the most cost effective cross-sectional dimension of the channel – width and depth. The slope of the channel is 0.01. Neglect free board. Mannings n = 0.011.
solve the compund curve table only asap plsss
A car is on a slope of 20 degrees. The handbrake can deliver 9 kN. What is the maximummass that can hold the handbrake? There is no more data... Urgenttttttttt
Please answer all otherwise leave it. I don't want single answer.. thank you a. On a mass haul diagram , the highest point of a loop indicats a change from cut to fill(in the direction of increasing stationing). True False b. A three level section requires one elevation reading at the centre line of the alignment and two others at the catch point locatios. True False c. The limit of economic haul would be expected to be less than the limit of free haul. True False
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
An open channel having a slope of 0.0065 is to carry 1.0 cum/sec. The channel material has an "n" value of 0.011. Find the depth of the most efficient cross section for a triangular section in mm. Answer in whole number.* 5 points