If the spring in (Figure 1) is compressed 3.2 in. against the 0.5-lb block and the block is released from rest. Figure < 1 of 1 k=5 lb/in. 1 ft Part A Determine the normal force of the smooth surface on the block when it reaches point = 0.5 ft Express your answer to three significant figures and include the appropriate units. μA ? N = Value Units Submit Provide Feedback Request Answer

If the spring in (Figure 1) is compressed 3.2 in. against the 0.5-lb block and the block is released from rest. Figure < 1 of 1 k=5 lb/in. 1 ft Part A Determine the normal force of the smooth surface on the block when it reaches point = 0.5 ft Express your answer to three significant figures and include the appropriate units. μA ? N = Value Units Submit Provide Feedback Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of the projected component of the F = 120 lb force acting along the axis BC of the pipe. Suppose that a = 7 ft and h = 2 ft. Express your answer to three significant units and include the appropriate units
A cantilever beam with a lumped mass W is constrained by a spring and a viscous dashpot damped, as shown in figure 3 below. If L= 60 in, EI= 10^3 lb-in^2 , c= 20 lb-s/in , W= 2000 lbs, k= 2kips/in, u0 = 0.5in, u0 (u with the dot in the middle up) = 10 in/s , determine (1) the displacement at t= 1.5 seconds, u( t=1.5) , and (2) the velocity at t= 1.5 seconds, u(t= 1.5) (u with a dot up in the middle again).
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
1. A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible weight. The water surface remains at the top of the gate. Determine the vertical component of the hinge force in kN to maintain equilibrium. Write your answer to the nearest three decimal places. Use unit weight of water 9.80 kN/m^3.
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
A block with weight W (W=75 lbs) can move vertically between two smooth walls. It is held by a rope which passes around three fixed rough pegs (coefficient of static friction u=0.25) as shown in the figure. Calculate the force F which will ensure that the block remains suspended.
A = 3 B = 4 C = 1 D = 0 kindly answer the magnitude and if possible the forces
A beam is subjected to uniform force w as shown in the figure below, E of the entire section is 30000 kips/inch^2, I is 240 in^4, if point A is supported by 0.003 rad clockwise before assembly, and point B is supported at Subside 0.3 inches before assembly, try to calculate the reaction force of point A and point B.
Situation 5. The column is used to support the floor which exerts a force of 3000 lb on the top of the column. The effect of soil pressure along its side is distributed as shown. 10. Replace this loading by an equivalent resultant force in lb. a. 3253.9 b. 4260.0 c. 3003.3 d. 3918.0 11. Specify where it acts along the column, measured from its base A in ft. a. 3.86 b. 1.62 c. 5.14 d. 1.4
A rectangular plate of width 3 m and depth 5 m is suspended vertically in a pool of water so that the top of the plate is 1 m below the surface of the water. What is the total force due to water pressure on one side of the plate? (Unit force should be in Newtons, N). specific weight of water (y)=9.81 kN/m³
Compute the resultant of the three forces shown in the figure. a.) None of the Above b.) 315.28 N c.) 836.90 N d.) 894.32 N e.) 948.27 N