if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #30 only is equal to ……………… SieveMassSizeRetained(gm)# 4#88.2#1660.5#3038.7#5025.2#20025.2Pan6.7

Given:- The total mass of the aggregate sample = 164.9 grams To determine:- The percent passing from…

Answered: if total sample mass of aggregate is…

Engineering

Civil Engineering

if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #30 only is equal to ………………

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 1: ProCoarse aggregate is placed in a rigid bucket and rodded with a tamping rod to…

Q: Draw a graph to show the cumulative percent passing through the sieve versus sieve size for…

A: A soil is categorized as well Graded soil if the particles of soil have wide range of sizes and are…

Q: Is it necessary to handle properly our aggregates prior to construction? If yes, how will it be…

A: Yes , it necessary to handle properly aggregate prior to construction. It is handled by : *…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: aTrial-1γd1=W2-W1V=69.6-20.3 lb0.5ft3=98.6lbft3Trial-2γd2=W2-W1V=68.2-20.3…

Q: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

A: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

Q: 1. Discuss how fine aggregate particles are removed from a sieve to be weighed. Explain the…

A: Brief Concept- The different particles of aggregates and sand are determined by the particle size…

Q: Draw a graph to show the cumulative percent passing through the sieve versus sieve size for…

Q: TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ±…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: The grading of three aggregates is given below. a) Calculate the percent passing for a combined…

A: Given: Results of gradation tests on three aggregate A,B and C is shown below Sieve size…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Given that, Dry rodded unit weight of aggregate : γb=1161 kg/m3 ⇒72.5 lb/ft3 Bulk dry specific…

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Volume of bucket =14L=0.494 ft3weight of bucket= 9.21kg=20.20 lbweight of bucket filled with dry…

Q: What is the percent passing on 4.75 mm sieve? b. What is the fineness modulus of the fine aggregate…

A: To find out the percentage passing on 4.75mm sieve and fineness modulus of fine aggregates.

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Given that, Dry rodded unit weight of aggregate γb=1410kg/m3⇒88 lb/ft3 Bulk dry specific gravity of…

Q: The data gathered from an experiment to determine the specific gravity of aggregates were summarized…

A: Given data: Weight of FA sample w1= 171.06 gm weight of SSD sample w2= 175.38 gm weight of…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given: Volume of bucket, V = 1/3 ft3 Weight of empty bucket, W1 = 18.5 lb Weight of bucket filled…

Q: Aggregates from three sources having bulk specific gravities of 2.753, 2.649, and2.689 were blended…

A: Given data: The specific gravities of three aggregates are 2.753, 2.649 and 2.689. The ratio of…

Q: For a fine aggregate, the value of fineness modulus was calculated to be 2.30. Is the particle size…

A: Fineness modulus indicates how coarse or fine an aggregate is. Higher the fineness modulus coarser…

Q: 4. A sample of fine aggregate weighs 501.2 g when SSD and 491.6 g when OD. The flask weighs 540.6 g…

A: The bulk specific gravity of fine aggregate is given by:Gsb=AB+S-C Where, A = Oven dry weight =…

Q: A sieve analysis test was performed on a sample of aggregate and produced the following result Sieve…

A: To find sieve analysis Percent passing Fineness modulus

Q: 46.5 kg of fine aggregate is mixed with 72.3 kg of coarse aggregate. The fineaggregate has a…

A: given data: fine aggregate: water content=2% absorption=3.4% weight=46.5 kg coarse aggregate: water…

Q: Aggregates from three sources having bulk specific gravities of 2.753, 2.649, and 2.689 were blended…

A: Given: For Aggregates from source 1: Specific Gravity = 2.753 Ratio = 70 For Aggregates from…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Void ratio = void ratio of a soil is a ratio of the volume of voids to the volume of solids. e =…

Q: Discuss the process of "Reducing field samples of aggregates to testing size".

A: Large field samples are reduced to smaller field samples to obtain a required size sample for…

Q: Calculate the percent voids between aggregate particles that have been com- pacted by rodding, if…

Q: Aggregates from two stockpiles, A and B having coarse aggregate angularity (crushed faces) of 40%…

A: Consider the given data For stock pile A percentage crushed faces =40% For stock pile B percentage…

Q: Discuss the effect of the amount of material passing the 0.075-mm sieve on the stability, drainage,…

A: Aggregate size has an effect on the relative properties of base materials as they constitute the…

Q: What are the main purposes of Sieve Analysis of aggregates?

A: purpose of sieve analysis Main purpose of sieve analysis is to determine the distribution of…

Q: sand particals does have liquid limit ? justify your answer.

A: Given data Sand particles Lliquid limit To find Does sand has liquid limit

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The given data is: Volume of bucket = 1/2 ft3 Weight of Empty Bucket = 20.3 lb Weight of bucket…

Q: In the Aggregate Impact Value test you get the following Total weight of Aggregate 344 grams %3D…

Q: Table P5.27 shows the grain size distributions of aggregates A, B, and C. The three aggregates must…

A: The solution is in step 2:

Q: Calculate the bulk specific gravity of combined aggregate if you know the specific gravities of…

Q: The sieve analysis results of two fine aggregates are given below in Table 1. a) Calculate the…

A: The expression for fineness modulus is given as FA1=∑100-%P100 % passing 100-%passing 100 0…

Q: from three sources having bulk specific gravities of 2.753, 2.649, and 2.689 were blended at a ratio…

Q: 1.3. Percentage of material retained between consecutive sieves. 2. Report percentages to the…

A: Sieve size Size in mm Amount retained Cummulative amount retained percent fineness 4 4.76 33 33…

Q: Samples of coarse aggregate from a stockpileare brought to the laboratory for determination of…

Q: What makes sampling as the most important step in assuring the quality of the aggregates?

Q: Three aggregates are to be mixed together in the following ratio: Aggregate A: 35% Aggregate B: 40%…

A: Aggregate percentages in the mix: Aggregate A:35% Aggregate B:40% Aggregate C:25%

Q: 2. A sample of fine aggregate weighs 501.2 g when SSD and 491.6 g when OD. The flask weighs 540.6 g…

Q: 25/ Find job mix formula by using mathematical method. Aggregate Specification Sieve Size A B C…

A: The final value of a complete mix design is a preferred mixture of aggregate and asphalt binder.…

Q: 4. A sieve analysis test was performed on a sample of fine aggregate and produced the results in…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Aggregate from two stockpiles, A and B having coarse aggregate angularity (crushed faces) of 55% and…

A: given values x1=55% x2=75%P1=45P2=55p1=30%p2=60%

Q: if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #50 only…

A: The given data is: Total sample mass of aggregates (WT) = 164.9 g

Q: Review ASTM D75 and summarize the following:a. Sampling aggregates from conveyer belts.b. Sampling…

A: ASTM D75 lays out the the rules and the precautions that are to be followed while collecting the…

Q: The table below shows the percent passing for an aggregate blend. Determine the following: 1. The…

A: Hi! Thank you for the question, As per the honour code, we are allowed to answer three sub-parts at…

Q: From the given data shown in the table below, determine the effective specific gravity of…

Q: 5.24 Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B…

A: Given:- Aggregate A-35%Aggregate B-40%Aggregate C-25% To find:- Percent passing each sieve for the…

Q: 5.32 Calculate the fineness modulus of aggregate A in problem 5.23. Is your answer within the…

A: Sieve size (mm) % passing % cumulative retained 25 100 0 19 92 8 12.5 76 24 9.5 71 29…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Percentage of voids is the volume of voids occupied by either air or water or combinedly both in the…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #30 only is equal to ………………

Sieve
Mass
Size
Retained
(gm)
# 4
#8
8.2
#16
60.5
#30
38.7
#50
25.2
#200
25.2
Pan
6.7

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

ASAP PLS U'LL GET A LIKE <33
It is desired to transport 20 cfs of water through a rectangular finishedconcrete (n = 0.012) canal that can be at most 5 ft wide. The slope of theland through which it passes is 0.0004. The depth of water, in ft, thatshould be expected is nearest: A. 1.83B. 1.28 (Incorrect Answer)C. 1.63 D. 1.01
Plz do fast
Is this way simplier to got AY, BY, AX,BX find out? Can u simplier that equations, i don't got 1.88kN and 0.38 kN. I only got 1.77 and 2 kN Thanks
SHOW COMPLETE SOLUTION PLSVALUES:Y = 53B = 5
R= 60
a = 4.5 m b = 33.0 kN/m c = 13 kN
A system that uses the FIXED and Universal otigin (0,0,0) is called how?
que3
Can you explain why for a. ha is 0.26 when it is not stated there and hb 2.4 when it should be 2.4+h-0.26
Q4/Use forth order R.K.Mto find z at t=0.5, with (h=0.5) and initial condition [z(0)=2] and xfrom O to 0.5, use four decimal places: f(t, z) = 4e%% - 0.5z O A)Y(0.5)=6.9953 (O B)Y(0.5)=4.9074 O ©)Y(0.5)=3.7516 O D) Non of the above
Calculate the following forces: CD BD AD