The data gathered from an experiment to determine the specific gravity of aggregates were summarized in the table below. Weight of FA sample (grams) 171.06 Weight of SSD sample (grams) 175.38 Weight of pycnometer with water (grams) 441.38 Weight of pycnometer with SSD sample and water 541.03 (grams) Weight of oven-dry sample (grams) 166.85 Calculate the bulk-specific gravity (dry). Round your answers to three decimal places.

The data gathered from an experiment to determine the specific gravity of aggregates were summarized in the table below. Weight of FA sample (grams) 171.06 Weight of SSD sample (grams) 175.38 Weight of pycnometer with water (grams) 441.38 Weight of pycnometer with SSD sample and water 541.03 (grams) Weight of oven-dry sample (grams) 166.85 Calculate the bulk-specific gravity (dry). Round your answers to three decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?
Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?
A laboratory technician performing a test on fine aggregates in accordance with ASTM C128 weighed the pycnometer filled with water reading 1201.8 g on the scale. He then took 502.3 g sample in saturated surface dry condition and poured into the pycnometer partially filled with water then filled it up to the calibrated mark. The weight of the pycnometer containing water and sample is 1516.1 g. After which he poured the content of the pycnometer in a drying pan and dried the sample in the oven. The resulting weight of the sample after drying was 494.9 g. Compute the following: a. Bulk Specific Gravity (oven dry) b. Bulk Specific Gravity (SSD) c. Apparent Specific Gravity d. Absorption in %
What are the differences between coarse aggregates coming from processing plants and coarse aggregates obtained under water in rivers?answer in 4 sentence
A sieve analysis test was performed on a sample of coarse aggregate and produced the results in Tablea. Calculate the percent passing through each sieve.b. What is the maximum size?c. What is the nominal maximum size?d. Plot the percent passing versus sieve size on a semilog gradation chart.e. Plot the percent passing versus sieve size on a 0.45 gradation chart.f. Referring to Table (ASTM C33), what is the closest size number anddoes it meet the gradation for that standard size?
Table shows the grain size distributions of aggregates A, and B. Answer the following questions and show all calculations: What are the maximum sizes of aggregates A and B?
A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 panAmount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.
"A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 pan.Amount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6 .Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.Calculate the fineness modulus of the sieve analysis results of Sample Problem
Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland cement concrete. Review the grain size distribution to determine if it meets all of the relevant specifications for use in concrete (i.e. gradation limits, fineness modulus and % fines). Refer to the specification for concrete aggregates (Table 7 – 10) below: Grain Size (mm) % Passing Cum %Retained 25 100 19 100 12.5 100 9.5 100 4.75 95 2.36 85 1.18 55 0.6 30 0.3 15 0.15 8 0.075 6 Fineness Modulus - write answer to two decimal places Percent fines - write answer to the nearest whole number % Meets Gradation Limits? - y/n (only type lower case "y" for yes and lower case "n" for no) Suitable for use in portland cement concrete subject to abrasion? - y/n (only type lower case "y" for yes and lower case "n" for no)
Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland cement concrete. Review the grain size distribution to determine if it meets all of the relevant specifications for use in concrete (i.e. gradation limits, fineness modulus and % fines). Refer to the specification for concrete aggregates (Table 7 – 10) below: Grain Size (mm) % Passing Cum %Retained 25 100 19 100 12.5 100 9.5 100 4.75 95 2.36 85 1.18 55 0.6 30 0.3 15 0.15 8 0.075 6
TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ± 5°C, then cool to room temperature. 2. Select suitable sieve sizes to furnish the information required by the specifications covering the material to be tested. Common sieves in millimeters are 37.5, 25, 19, 12.5, 9.5, 4.75, 2.36, 1.18, 0.6, 0.3, 0.15, and 0.075 mm (11 2 in., 1 in., 3 4 in., 1 2 in., 3 8 in., No. 4, No. 8, No. 16, No. 30, No. 50, No. 100, and No. 200). 3. Nest the sieves in order of decreasing size of opening, and place the aggregate sample on the top sieve. 4. Agitate the sieves by hand or by mechanical apparatus for a sufficient period. The criterion for sieving time is that, after completion, not more than 1% of the residue on any individual sieve will pass that sieve during 1 minute of continuous hand sieving. 5. Determine the weight of each size increment. 6. The total weight of the material after sieving should be compared with the original weight of the sample placed…